optical encoder disc 3d models
23898 3d models found related to optical encoder disc.thingiverse
Parametric encoder disc for mounting on a round shaft. Original design is for an 4WD RC car and mounded on the drive shaft. By default it fits the Exceed Magnet RC truck drive shaft. Updated to be used with either optical sensor or magnetic/hall...
cults3d
This encoder is made for the RepRap project, but it can be used for any project where you wish to determine angle or rotational speeds. ...The encoder on the extruder is an important step towards better 3D print quality (constant plastic flow rates).
thingiverse
This is a simple 3D printet Tacho encoder (optical) with 18 steps pr. ...round.
grabcad
Optical Encoder A rotary encoder, also called a shaft encoder, is an electro-mechanical device that converts the angular position or motion of a shaft or axle to an analog or digital code. There are two main types: absolute and incremental...
prusaprinters
This is a simple 3D printet Tacho encoder (optical) with 18 steps pr. ...round.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>Ender 3</p></div>...
thingiverse
Grove Rotary Encoder Testsetting Baseplate for Sensor and Optical rotary Encoder disc Grove Sensor http://wiki.seeedstudio.com/Grove-Optical_Rotary_Encoder-TCUT1600X01/
prusaprinters
Knob designed to fit on a cheap Chinese optical encoder with my remote Elecraft K3 Knob project. ...Fits a 1/4" diameter shaft.</p> Category: Electronics
thingiverse
Knob designed to fit on a cheap Chinese optical encoder with my remote Elecraft K3 Knob project. ... Fits a 1/4" diameter shaft.
thingiverse
Customizable optical encoder for motors and shafts. ... Print Settings Rafts: Doesn't Matter Supports: No Notes: Note: If you set the number of slots very high or make the encoder very small you may have trouble printing unless you are using a very...
thingiverse
Work-in-progress project to use a CD as an optical encoder for experiments. I'm writing some code for an AVR-based project to count up and down, depending on which way one spins the CD. All parts designed in SketchUp. These parts are fine-tuned...
thingiverse
... I have designed for a music robot I am building. ...The gear ratio makes the small movement on one end become a large movement on the other. The side that gains the large movement is then attached to a rotary encoder to increase its resolution.
thingiverse
This is just a mockup of a cheap optical sensor board from Aliexpress. You can find it using the search terms "j34 optocoupler lm393." I posted this as a remix because I found this other part using the board. I thought it would be nice to have a...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1679204 Instructions Using the following options: set_screw_nut_thickness = 2 hub_diameter = 25 set_screw = 1 set_screw_diameter = 3.5 set_screw_nut_diameter = 5 shaft_flat_depth = 1.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1679204 Instructions Using the following options: outer_diameter = 50 rim_width = 1.75 shaft_flat_depth = 1 hub_height = 4 shaft_goes_through_encoder = 1 set_screw_nut = 1 wheel_height = 5.1...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1679204 Instructions Using the following options: set_screw_nut = 1 outer_diameter = 30 set_screw = 1 slit_ratio = 0.5 slit_count = 100 set_screw_diameter = 3 shaft_type = 2 wheel_height = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1679204 Instructions Using the following options: hub_diameter = 5.25 hub_height = 5.5 set_screw_nut = 0 shaft_type = 0 slit_count = 60 shaft_diameter = 3 set_screw_nut_thickness = 2 rim_width =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1679204 Instructions Using the following options: wheel_height = 1.3 set_screw_diameter = 3 set_screw_nut_thickness = 2 rim_width = 0.75 slit_count = 30 slit_length = 2.5 shaft_flat_depth = 1...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1679204 Instructions Using the following options: set_screw_nut = 0 shaft_flat_depth = 1 slit_count = 30 rim_width = 1.25 set_screw = 0 slit_length = 2.5 wheel_height = 1.3 set_screw_diameter =...
pinshape
This is an openSCAD file that will let you create a pendant/encoder disc that has your text on it. You can wear it as a pendant or use it as an encoder disc. ...Some setting are available to customize it.
thingiverse
This is an openSCAD file that will let you create a pendant/encoder disc that has your text on it. You can wear it as a pendant or use it as an encoder disc. ...Some setting are available to customize it.
thingiverse
This holds 5 discs with some room to spare so you wont have to struggle to get your discs in and out even if the print isn't perfect. Solidworks file included in case you feel like messing around to make your own based off this. ...Print Settings...
thingiverse
Take a look at my Blog to get more informationshttp://coolrobotprojects.blogspot.co.at/ The open-Frameworks-Code that generates the Gradient/Encoder-pattern:https://github.com/thunderbug1/encoder_pattern_generat The generation of the non radial...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1679204 Instructions Using the following options: set_screw_nut = 1 wheel_height = 2 rim_width = 2 slit_ratio = 0.5 set_screw = 1 hub_diameter = 25 set_screw_nut_diameter = 5 slit_count = 24...
grabcad
Board of optical encoder pololu with texture and 5-teeth encoder wheel.
grabcad
Miniature encoder with 30 steps of absolute position is implemented with 5 optical sensors generating single track grey code.
thingiverse
Logitech G27 Optical Encoder 30 slot Logitech G27 Encodeur optique 30 slot pour nouveau G27 et Driving Force GT version 2