optoma mount 3d models
341511 3d models found related to optoma mount.thingiverse
A mount for the Optoma UHD5 and 3 series. I used a standard hitch (cheap and strong) and then designed a holding clamp. ...The hitch is centered equal distance from the three mounting holes.
thingiverse
Wanted to use the mount designed by shadowtag, however the mounting holes for the Optoma HD146x were slightly different. Simply moved one of the mount pillars over to match the bolt pattern on my projector. ...Install instructions are the same as the...
thingiverse
Optima Beamer Mount (applied on HD142X). The demonstrated one I currently use is printed in PLA, density 50%, 0.4 nozzle. When printed in ABS and higher infill settings will make it even stronger. Add M4 Screws 25 mm & 55 mm. Enjoy! ...Printed parts:...
thingiverse
printed with petg, 20% infill, pla should also work
thingiverse
... Remixed reinforced stiffer ceiling mount for many Optoma projectors whit these measures: 100 x 100 x 110 mm triangular M4 holes mount. Adjustable in any direction and screwed in for permanent hold. These parts are reinforced, just in case !!!
thingiverse
I will update this post after some time to report about the sturdiness of the mount and if I discovered potential stability issues. For now it appears to be very sturdy. ...I used about 600g of PLA for this, because I am a bit paranoid about having a...
thingiverse
... at the bevel to avoid removing supports. There are ways to avoid this, but for now, i'm proceeding as is. Optoma H184X Projector: https://amzn.to/3jpfjzr Ceiling Mount: https://amzn.to/2YJEg0K 80" Portable Screen: https://amzn.to/3jmrUDt
thingiverse
This is an adapter for the Optoma HD27HDR projector (and potentially other Optoma projectors with the same mounting pattern) to a standard VESA 200x200 pattern for ceiling or wall mount. ... OnShape:...
thingiverse
The is a 3 point adjustable mount for the Optoma GT1080.http://www.optomausa.com/projectorproduct/gt1080 The projector has such a short throw that it's great for setting on my bed and watching movies on the wall. However, the projector needs to be...
prusaprinters
The is a 3 point adjustable mount for the Optoma GT1080. http://www.optomausa.com/projectorproduct/gt1080 The projector has such a short throw that it's great for setting on my bed and watching movies on the wall. However, the projector needs to be...
thingiverse
I have redesigned the parametric Bottle to some Feets for my Optoma Beamer. They are adjustable in height and have holes for M3 or M4 Screws, to screw them on any Board. But works well without screws, too. The parts should be customizable in...
thingiverse
Hi this is a model made by myself for my OPTOMA UHD38! It woeks perfectly! ... Enjoy it!
sketchfab
Recreated the classroom’s optoma projector. Part of my class project of recreating the classroom we are in. ...I added the lighting so it could be seen better.
3docean
======================================================== Optoma Projector HD141X DLP Characteristics: - Ready for close up renders - No NGons - Mostly quads (triangle rate below 9%) - Clean edge flow, sub-dividable topology - Real world scale...
thingiverse
I needed to mount a Optoma projector onto a Manfrotto tripod for a projection mapping project. Because I couldn't find an adaptor I could buy I designed one on my own. I hope you find it useful too! ... For the three lock bolds I used M3 screws and...
thingiverse
I can't believe Optoma didn't provide a lens cap for this projector, instead it came with a vacuum formed piece of plastic taped onto the front. This design is press fit, so you may have to print a test to make sure your filament doesn't shrink...
cults3d
I can't believe Optoma didn't provide a lens cap for this projector, instead it came with a vacuum formed piece of plastic taped onto the front. This design is press fit, so you may have to print a test to make sure your filament doesn't shrink too...
cgtrader
======================================================== Optoma Projector HD141X DLP Characteristics: Ready for close up renders No NGons Mostly quads (triangle rate below 9%) Clean edge flow, sub-dividable topology Real world scale (centimeters)...
thingiverse
This is a 3D model of the Optoma ML550 projector. Since from what I've learned, the ML750e model uses the same housing and button having difference only in electronics and/or LED for more brightness, I marked it as a ML750e too. This model is not...
thingiverse
A Simple cover for Optoma HD142x proyector. ...Print Settings Rafts: No Supports: No ...
thingiverse
3D printed connector for an 80mm x 80mm x 10mm USB fan - Print and use at your own risk - (NOT AN AFFILIATE LINK - https://www.aliexpress.com/item/4000088777368.html?spm=a2g0s.9042311.0.0.75904c4dXhH3vZ) Parts - 4x M4x16mm screw 80 x 80 x 10mm USB...
myminifactory
Our Optoma projector came without a lens cap, to keep the dust out of the lens I decided to design a lens cap myself. The lens cap has a small tab with a 2mm hole for a string so you can't lose of forget the cap if you use the projector on different...
thingiverse
Lenscap for Optoma HD144x and 143x Beamers. Fits perfect for my device. I have printed it with black PLA. This version is more tight than the version from MarkDirk and has double borders, but no lug because I don't need it. ...You can also check...