opus bt c3400 3d models
2360 3d models found related to opus bt c3400.thingiverse
My Battery charger was constantly being knocked off the shelf by my cats. I figured if I put some batteries around the edge it would add a little weight. Besides, now I have a location for holding charged batteries and batteries which need to be...
thingiverse
The fan in the BT-C3400 battery charger is a horrible little thing that eventually fails in most units. A replacement is hard to find, and it'll fail again anyway. This adapter fits a standard 35mm 12V fan as a replacement. ... Mounting requires (4)...
thingiverse
This is a adapter for my LI-PO accu's with JST 2 pins connector. ...Its clamped between the sliders of the Opus BT-C3100. ...I've used a piece of 2x8 cm pcb (85644J2H) for th JST male connector and copper strips for the contacts.
thingiverse
This is a wall mount requested from soneone in my DIYEnergyPack discord server to hold an Opus BT-C3100
thingiverse
Easy way to change charging voltage on OPUS BT-C3100
thingiverse
Opus BT-C3100 Battery Charger wall mount. ...With cut outs for ventilation and jacks.
thingiverse
It's a remix of Opus BT-C3100 - 80mm Fan Mod by ShrimpStar with vertical fixation. ... I use wood screws Ø3.5x16mm.
thingiverse
A simple support/wall/Ikea Skadis mount for the OPUS BT-C3100 battery charger. ...Other supports available rarely take in account the air intakes.
thingiverse
A simple way to change the charging voltage on the OPUS BT-C3100, the modified part by Kirux0 (https://www.thingiverse.com/thing:3292305)
thingiverse
Wall brackets to mount the OPUS BT-C2000 model battery charger. Found the exact bracket I had in mind via https://www.thingiverse.com/thing:4322624, but it was designed for a newer model and did not fit the BT-C2000, mainly due to difference in...
prusaprinters
A simple support/wall/Ikea Skadis mount for the OPUS BT-C3100 battery charger. ...Other supports available rarely take in account the air intakes.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p...
prusaprinters
It's a remix of Opus BT-C3100 - 80mm Fan Mod by ShrimpStar with vertical fixation. I use wood screws Ø3.5x16mm. Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: NoResolution: 0.2 Infill: 15% Filament: IceFilament PLA Black ...
thingiverse
This is a replacement case for BT-C3100 battery chargers. this permist to have better cooling thanks to many openings and to add an extra 60mm fan with a voltage converter to tune the fan speed. this way you can choose your place between noisy...
thingiverse
Tilted mounts for the Opus BT-C3100, for both desktop and wall mount. ... Prints with no supports.
thingiverse
https://www.thingiverse.com/thing:3292305 This is a support block under the OPUS BT-C3100 charging voltage regulator slider by Kirux0. ... Without this part the slider fallen in to the bottom case and I found this solution.
thingiverse
I split samxthomas's Opus 80mm Fan Mod (https://www.thingiverse.com/thing:2744027) in two, because my printer (Monoprice i3 mini) can't fit the whole model on the print bed. There's a dovetail pattern in the bottom of it that will help interlock the...
thingiverse
The BT-3100 is a very good charger but unfortunately the original fan is very loud. i use a Noiseblocker Super Silent Fan 40x40x10 XM2. The Airflow of these Fan are very good and the fan are very silent. The installation is very simple and...
thingiverse
Since Opus began, he has so far been a political operative, a garbageman, and a newspaper ombudsman – but he was most often depicted as a syndicated cartoonist. No supports are required. If you have the proper filament colors, no painting is...
myminifactory
Since Opus began, he has so far been a political operative, a garbageman, and a newspaper ombudsman – but he was most often depicted as a syndicated cartoonist. No supports are required. If you have the proper filament colors, no painting is needed....
cults3d
Since Opus began, he has so far been a political operative, a garbageman, and a newspaper ombudsman – but he was most often depicted as a syndicated cartoonist. No supports are required. If you have the proper filament colors, no painting is needed....
thingiverse
I made a slight bump at the two ends so you can use a nikkel strip as a terminal and have it rest against the plastic.
thingiverse
Habe es bei 30% Infill Gedruckt Down converter von 12v auf 5v
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189264 Instructions Using the following options: topClearance = 0.2 lidThickness = 2 boxHeight = 22 textThickness = 2 lidEdgeThickness = 0.5 boxWidth = 59 bottomThickness = 1.6 cornerRadius = 5...
thingiverse
quick remix with mounting tabs for the v2 charger
cults3d
Just a coaster with Fuente Fuente Opus X logo. ...Diameter is 9.5cm / 3.74inch