orange pi 5 case 3d models

Laser cut template (Inkscape). ...Acrylic case for Orange Pi One.

Raspberry Pi 5 and Active Cooler Case, with reset buttonThe objective was to design a sturdy ventilated case that would suit the Pi Active Cooler.The wall thickness chosen in 2.5mm which allows sufficient depth for a recessed panel for the HDMI and...

The screens I'm utilizing can be found at: https://www.amazon.com/Elecrow-800x480-Interface-Supports-Raspberry/dp/B013JECYF2/ref=sr_1_2?dchild=1&keywords=Elecrow+5+inch&qid=1585443770&sr=8-2 The design is tall to accommodate a 40mm fan blowing...

Do pobrania obudowa na Raspberry Pi model 4B, obudowa zaprojektowana na wysuwany dodatkowo dysk twardy 2.5 cala sata/usb wszystko w jednej zwartej obudowie do montaży na ścianie…. Zapraszam tez na...

Do pobrania obudowa na Raspberry Pi model 3B, obudowa zaprojektowana na wysuwany dodatkowo dysk twardy 2.5 cala sata/usb wszystko w jednej zwartej obudowie do montaży na ścianie…. Zapraszam tez na...

I combined the base clip section of the spool holder with this wonderful Raspberry Pi case so it would mount on my Taz 5 to hold my OctoPi board. Changes from original case: I thinned out the top (slotted side). It was unnecessarily thick and...

Case for the Raspberry Pi 4 with a 3.5" TFT display module. Enlarged holes around micro HDMI ports to facilitate cables with larger ends, adjusted positioning of port holes, and added a view slot so the PWR and ACT LEDs can be easily seen. Added...

# Features: - "quick release" for drives (small nobs instead of SSD mounting screws) - optional ability to additionally secure drives with traditional mounting screws - optional 40mm x 10mm fan mount (tested with NF-A4x10) - SSDs are not required...

Fitting Case for a Raspberry Pi 3 B+ with an 3.5" screen. Te bottom part is extended so that the GPIO Pins of the screen are reachable and hidden behind the frame when connecting them. The Screen fits perfectly in the frame. Only thing to do is...

A compact case and a sturdy stand for the Raspberry PI, complete with a 3.5" screen, are designed to work seamlessly together. The case effortlessly glides into place on the stand without requiring any screws or glue. For added convenience, the stand...

This is a case for the raspberry pi 4 with an adafruit 3.5 tft screen. In the bottom of the case, you can use a noctuna fan NF-A4x10 5V. I used a 5V fan, so I can use the voltage of the USB port. The bottom and top is clicking, no screws needed. I...

... case for the Raspberry pi. ... This case has a top to accommodate the Sparkfun LCD Touchscreen HAT. There is also a slot to store the stylus. The pi can be screwed into the bottom, but the case fits tight enough that usually do not screw it down.

An orange hued plastic enclosure is what's being described here.

Summary Raspberry box based on this design: http://www.thingiverse.com/thing:604915 (Sleeve Case for Raspberry Pi B+) - Thanks Walter!! I recently added a case to fit a 2.5-inch hard drive with some spare space for a SATA-to-USB converter. I removed...

I designed this case for my 5-inch touchscreen LCD, which I purchased from Aliexpress, to use with my Raspberry Pi. Ideally, this case is intended for OctoPrint and OctoScreen/OctoDash, but it could work just as well for any other application. In my...

The pictures show what this case looks like when you hold a Banana Pi board and a standard 2.5-inch HDD. We've confirmed compatibility with both original Banana Pi and Banana Pro models, so feel free to use them together seamlessly. Before we begin,...

https://www.thingiverse.com/apps/customizer/run?thing_id=58001 Instructions Using the following options: iPhone version: 2 Pattern overlap: 18 Image scale: 100 Case thickness: 2.4 Primary color: red Taper: 3 Case type: 1 Swidth (case): 6.17 Stickness...

This design, combined with this case, and my chosen SSD (all 2.5" SSDs share the same form factor), none of the connectors are obscured or covered. The case has screws on the bottom, and the last iteration had a flawless "tab" that fit between the...

This case is specifically designed for the Raspberry Pi 3 (Model B or B+) or 4, and comes equipped with a 5-inch capacitive touchscreen display. The display uses the Pi's "DISPLAY" connector and a ribbon cable, as shown in photo 2. It can be found...

Raspberry Pi Concept case

Raspberry Pi Concept case

I'd be happy to implement it.  The reason that I designed the rear lcd and pi case as separate and not as one piece is due to the complexity during printing. If the case rear is a one piece part, you'd have to print with supports and the overall...

I'd be happy to implement it.  The reason that I designed the rear lcd and pi case as separate and not as one piece is due to the complexity during printing. If the case rear is a one piece part, you'd have to print with supports and the...

This challenge led me to create a simple bracket that slides over the electronics cabinet of the FT-5, preventing the Raspi case from being knocked off and positioning it at a sufficient height. With a long ribbon cable, I can now mount the camera...

I built a case to house my Raspberry Pi 3B+ and 5-inch Touchscreen (XPT2046) that I bought from Jaycar here in New Zealand. Using it for OctoPrint with TouchUI. NOTE: This case won't fit the Raspberry Pi 4. The Pi 4 has its Ethernet port and USB...

Raspberry Pi 5 and Ice Tower Cooler CaseThe objective was to design a sturdy ventilated case that would suit the 52Pi Ice Tower Cooler.The wall thickness chosen in 2.5mm which allows sufficient depth for a recessed panel for the HDMI and USB...

The Case for Banana Pi/PRO features an accommodating space to fit your 3.5-inch Hard Disk Drive, ensuring effortless storage integration while utilizing the entire motherboard compartment, maintaining its durability. Its sleek and modern design...

I've designed a holder for a 5-inch Raspberry Pi case display holder. Raspberry Pi 3 features an 800x480 resolution screen. Check out this thing on Thingiverse: https://www.thingiverse.com/thing:3374265. You can use this fan:...

I designed this highly compact shell specifically for my Raspberry Pi Zero W and 5" LCD display, mounting it securely on my Anet A8 while allowing me to run Octoprint with an intuitive display. This project required more customization than most...

Since I often need to swap SSDs and need a place to mount my fan, I designed a new case. Compatibile with:- Raspberry PI 1B+/2B/3B/3B+/4B- 2.5 inch SSDs (7mm height)Note: The spacing between the two SSDs is 5mm. ...Make sure you are not using thick...