otterbox car mount iphone 6 3d models

Remix on an iphone otterbox tripod mount to use a standard gopro mount. ...Should work for iphone 6,7,8 Otterbox case

Thanks to botberg for creating this mount. ...I simply resized it to fit an iPhone 6/6s with an Otterbox case. Also Sorry for the low light. ...I can never get black prints to show up well on camera.

http://www.thingiverse.com/apps/customizer/run?thing_id=594489 Instructions Using the following options: ChargerZ = 5.5 ChargerX = 9 holediameter = 3 CScrewHoleLeft = Yes text = countersink = 3 CScrewDiameter = 3.85 Slack = 1.0 Height = 60...

Download and use this 4 part iphone 6 case also works for iphone 6s. ...enlarge the camera hole for iphone 7. i am using the iPhone 6 halo case design as the back of my case made by Girgis designs Print Settings Printer: Da vinci jr 1.0

... for your car vent. ...You can insert your lightning cable into the custom slot so that your phone charges when holstered. The holster attaches to your car vent (or any other mounting surface) with ties straps in the holes provided. Enjoy! ...

IPhone 11 with Otterbox Defender Case Car Mount Simple solution to mount my phone on my dash board top while keeping the Otterbox Defender case fitted Plan to redesign at some point to have wireless charging when a suitable charging pad is found to...

One mount for the door for my printer, one as a holder for my passenger side headrest to keep my daughter entertained in the car, and another as a mount on the wall for charging. This current design has been revised for all three uses. The three...

Car mount for iPhone 6+ with no case. Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=526257 This thing was made with Tinkercad. ...Edit it online...

Car mount for iPhone 6+ with no case. Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=526257 This thing was made with Tinkercad. ...Edit it online...

iPhone 6 car mount meant to be attached to the vent, holds device very firmly and will not come out until you want it to.  Slim design means that none of the screen is obstructed. ... The clip on the bottom can be broken off so that the AUX input is...

phone mount made to go into car vent, has a fair amount of wiggle room so that a small case will fit on the phone while its in the clip, works fine with a naked iPhone too, be warned that the vent that it is in needs to be shut off during winter...

I made this iphone mount to hold my phone in either the vertical position while playing music in my car, or in the horizontal position to act as my gps. recently I had been having to make many trips up to 7 hours away and I was using my phone as a...

This is an early version of a car mount for an LG V30 wearing an Otterbox Defender Series case. An optional wireless charger version is available. This should work with similar diy wireless charging kits. This is assembled using super glue for the...

Speaker stand made to fit an iPhone 6 with an Otterbox case. The three pieces have printed very well for me on my Z18 and they don't require much cleanup. The speaker bell makes for very crisp low-volume sound, great for background listening. It can...

iPhone 6/6+ CD Tray Mount converted from inches to millimeters

This iphone mount is 3D printed in PLA and is mounted in my car, This works well for me. I/m using the standard version and I'm not having any problems damage whatsoever but for the cousius i recommend the Kenny version with piece of fabric glued to...

This landscape cd mount for the iPhone 7 with an otterbox case is excellent for gps. The CD insert is 4.5 mm high and fits snugly in the CD opening of a 2016 Subaru Crosstrek. The lip on the tray is small but the face of the radio is angled a little...

Customized version of http://www.thingiverse.com/thing:526257 This was an attempt at making a car mount for a Note 4... but the dimensions were a wee bit too small and accidentally fits a iPhone 6 Plus. Ummm... yay? ... Created with Customizer:...

This thing was made with Tinkercad, It is a Remox of Cqdude's iphone 6 holder. This one has been flipped so the phone site lower. Might need to print with some supports for the CD prongs and also top. Note model prints upside down. ...Print took 4...

The cradle is designed to hold an iPhone 6 Plus that is in an Otterbox Defender series case. Including while being attached to my "Ingress pack" (http://www.thingiverse.com/thing:661257) The cradle's "peg" fits into the cradle holder (in two...

This is a frame for mounting an iPhone 6 with an OtterBox case on a wall with a slot for headphone and charging cable on the side.

Made this for a friend. ...It fits the iPhone 6 with OtterBox Defender case (http://amzn.com/B00N1AG5BO)

iPhone 6+ charging station (with Otterbox case). I found several other models but none that took into account the size of the phone with the Otterbox phone case. I designed this using Fusion 360 and designed it so my phone fit with the case on. I...

I needed an adapter for my Mavic Air to hold my iPhone 6s with an Otterbox case.

The iPhone 6 dock that quix posted recently worked flawlessly with the iPhone 6 but not with a case like the Otterbox. I redesigned the dock from the ground up. There is cable channel on the base, threading hole and a nice place for the charge cover...

I couldn't find a design for a charging station for an iPhone 6 with an Otterbox case that also had an Apple Watch dock. So I used Shodan's design, http://www.thingiverse.com/thing:1051928, as inspiration and designed my own in 123D Design. This has...

This doesn't look like much, as you can see, but this is actually the exact measurements for the iPhone 6 Commuter Otterbox case, for those who want to make their own holder, but don't want to take your case off, you can use this template. How I...

Modified the iPhone 6 dock by emadshaabani (thing #492101) to accommodate an Otterbox Commuter case, and have optional cable routes with good strain relief on the cable itself. I did have to drill the slot of the male-end of the cable with a 1/4"...

I originally designed this as a place to put an iPhone6 (w/case) when charging on my desk, but have since found that it also works well on the dash of my car when using a phone for navigation. Just simply plug in the phone and drop it. ... It looks...

The cable is common at frys and amazon its madeby Cirago See linkhttps://www.amazon.com/gp/product/B00ZKTFXEO/ref=pd_sbs_107_6?ie=UTF8&pd_rd_i=B00ZKTFXEO&pd_rd_r=BQWQZYVV6S8YSBQZ6WXF&pd_rd_w=h2pEC&pd_rd_wg=OtVie&psc=1&refRID=BQWQZYVV6S8YSBQZ6WXF The...