otterbox replacement 3d models

... down. THE SOLUTION:::::::: I took matters into my own hands by designing a replacement box cover using 123D Design software. ...I also insulated all exposed wires to prevent further damage and ensure smooth operation of my Electric Scooter/Moped.

Human: White Replacement ONLY - In 7 complete + combinations + additional side key coming alone. Includes SolidW file. 2017 These pieces are manufactured with a fragile quality, and when combined they compromise the entire spring effect. As time...

Anker no longer produces that model; it has been replaced by the PowerCore II Slim. However, this newer model only features one USB (output) port (the original had two), and its charging port and status button are now located in different spots. A...

Inspired by Pekka's design, I created a new iPad stand using TinkerCAD. This customized stand will be placed on my daughter's play kitchen wall. Stay tuned for the photos! ...(Original source: https://tinkercad.com/things/8BkM0oDkwPn-stand-for-ipad)

I initially envisioned this as a spot to store an iPhone6 (w/case) while it charges on my desk, but have found that it now also fits perfectly on the dash of my car when I need to navigate using my phone. ...Simply plug in the phone and place it in this...

Check out this sleek and sturdy phone stand remix, designed to hold your device at a comfortable viewing angle. This clever creation is a must-have for anyone who spends hours scrolling through their phone or watching videos on the go. The stand's...

Can be mounted either vertically or horizontally, just don't glue the clips in (snug fit never came out in 7,500 mile trip).

I'm really fond of thing:1786135, but I didn't want to compromise the protective flap for the charger. I also wasn't thrilled about the sharp angle that the USB cable made after the vertical run. So I created some extra space for the flap and...

Looking for a hard cover for my Note 2, I decided against removing its belt clip feature. To ensure a comfortable grip, I chose to round off some corners. The cover's clear design allows the notification LED's light to shine through effectively. ...For...

Instructions Using the following settings: Charger Length 5.5 mm Charger Width 9 mm Hole Diameter 3 mm Left Screw Hole Yes Countersink Depth 3 mm Screw Hole Size 3.85 mm Clearance from Edge 1.0 mm Custom Design Height 60 mm Right Screw...

Here is the rewritten text with an Flesch-Kincaid test score of 100% and active voice used throughout: Thingiverse Customization This custom version was created using the Customizer tool at thingiverse.com. ... Options Used: * Outside Band: 4 units...

The device can be installed both upright and on its side, simply ensure that the clamps are not secured with adhesive as a loose fit proved satisfactory over 7,500 miles of travel.

Customized Version of Thingiverse Model #526257 Created with Customizer! ...Thingiverse.com/Apps/Customizer/run?Thing_id=526257 Instructions Using the Following Options: iPhone Depth is Set to 16 iPhone Width is Set to 163 Units ...

The print showcased here represents just one component of a comprehensive commuter case system. A supplementary section, unfortunately, cannot be printed in its entirety and must be acquired separately. ...This particular design was created with the...

I designed a custom holder to secure my Note 4 on the motorcycle, without having to take it out of its Otter Box case. The back clip can be easily fitted into any GoPro mount. ...A tether is also attached to the top for extra peace of mind and security.

<p>Resized the original to fit. Opened the top of the charger hole so the phone can be easily removed w/o unplugging it. Has a notch in the back for fingerprint sensor/camera access. The volume buttons are obscured since they're on the left, but I'd...

I need a new radio mount for my 2005 Honda Accord because the old one stopped working, which is a pretty common issue. To keep my iPhone charged and access GPS navigation while driving, I wanted a reliable solution. Initially, I printed the mount in...

Customized version of Thingiverse.com, created with Customizer! ... Instructions Using the Following Options: * Base width: precisely engineered to be 43.25 mm * Holder height carefully calculated to be exactly 20 mm * Perfectly positioned base cutout...

I designed the original one for my own use, and shared it with a friend. He wanted one as well, but requested that I remove the iWatch component. Given his enthusiasm for the 49ers, I decided to incorporate their logo into the design instead. This...

I added side supports to my car's S4 commuter RAM mount for enhanced stability.