over the cubicle coat hook 3d models
2708191 3d models found related to over the cubicle coat hook.thingiverse
... nuts in 10/32 threading. Load the nuts into the bottom of the backstop and the screws go on top of the slotted main body. Then just adjust and tighten the screws to the desired wall thickness and viola you have one handsome looking cube coat hook.
thingiverse
Fits over the top of my cubicle wall and can hang my coat, hat and shop apron on it. ...Your cubicle wall size may vary.
thingiverse
A coat hook for the end of a cubicle, with two hooks, so you can share with your deskmate (or not).
thingiverse
I wanted a coat hook for my cubicle, but the way it's set up the only place I could possibly put one was on the end of the cubicle wall, so I made this.
prusaprinters
A simple coat hook designed to fit a 1 cm glass cubicle wall. Print instructionsA simple coat hook designed to fit a 1 cm glass cubicle wall.
thingiverse
A remix of kitlaan Cubicle Hook Thinghttp://www.thingiverse.com/thing:10396 This remix is a 2-piece coat hook. Some 3d features were added to the hook so it extends beyond the cubicle track to reduce side-to-side movement. Designed to reflect the...
thingiverse
This model is a over the door hook designed to fit a standard 1 3/8" thick interior door. ...The three hooks are staggered to allow for easily hanging multiple coats.
thingiverse
Update 1/31/2017 My cubicle track is deeper than the original, so I added additional offset from the hooks in the v2. I also removed one of the three hooks as 2 is more than enough for strength and stability. ...Remixed Kitlaan's Cubicle Hook to be more...
thingiverse
a coat hook for hanging coats hats headphones...anything at the office
thingiverse
However the original hook didn't fit our cubicles and after many revisions and suggestions from co-workers ended up with this design. The edges have been rounded, cut out some filament in the middle and it's wider so it fits tighter and slips off...
prusaprinters
<p>Printed with 20% infill. ... Cubicle wall thickness 2 ¼" (57.15mm) x 1" (25.4mm) thick. STL file provided so you can change the dimensions if needed.The printer used was enders 3 S1.
thingiverse
I was tired of bending paperclips to make coat hooks on my cube wall at work so I made this! It will surely need to be modified to meet your cube wall, but this thing may be the spitball you needed to design your own. ...
prusaprinters
Print in PETG, as PLA will be too brittle and will breakThis is designed to have a stress concentration at the root of the hook so that it will break before the glass cubicle wall, should the hanging coat get tugged on.
thingiverse
The internal feature of this coat hook is .9" The sign the part was intended for is about .825" thick. This was a bit loose, but I was able to pinch the part as it cooled so that it fit tighter. I will probably change the internal width before...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=102974 Instructions Using the following options: hook_radius = 15 clip_angle = 2 top_and_back_thickness = 4 clip_depth = 77 inner_hook_buttress = 1 hook_and_front_thickness = 4 clip_length = 55...
thingiverse
Edit it online https://www.tinkercad.com/things/0uBJ7YHlS8j This is a nice coat hook that fits over the top of most 2.75 inch wide cubicle walls. This one is for a wall with a slight arch at the top. I made it flat at first but an arch fits much...
thingiverse
This is designed to fit over the metal top rail in our office cubical s. I adjusted it to fit our cubical exactly, so some adjustment might be required for different manufacturers. Pretty simple to print, print it on its side with no supports. ...
thingiverse
This is a very heavy duty coat/backpack hook for cubicles with 3" thick walls. It can hold 30+ lbs when printed in PLA with 4 perimeters @ 200 micron layers. It has a saddle-shaped hook to keep the edges from digging into the handle of your bag,...
prusaprinters
This is a very heavy duty coat/backpack hook for cubicles with 3" thick walls. It can hold 30+ lbs when printed in PLA with 4 perimeters @ 200 micron layers. It has a saddle-shaped hook to keep the edges from digging into the handle of your bag, and...
thingiverse
... a few minutes in Fusion360 later. ... This pictures of the printed hook are after I shrunk it 25% in Simplify3D on the width. As designed it is two inches wide. I slipped it onto the partition and fits like a glove and supports over 30 pounds. ...
thingiverse
Find a coat hanger and hang that clown suit right behind you on the cubicle wall! Now, get back to work, YOU!! [sour glare] :) If you found this useful, please share your work and be sure to peruse my other submissions which are almost as varied as...
thingiverse
... I only used 10% infill. Going to try it out today and see how it holds. I might have some revisions to make. Added a second hook that is a little wider and has some extra support in the lower hook area. ... Still works with the same batman logo.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=102974 Instructions Using the following options: hook_and_front_thickness = 4 number_of_hooks = 2 clip_angle = 2 first_hook_offset = 65 clip_depth = 78 width = 25 hook_radius = 15 hook_style =...
thingiverse
A couple coat hooks for the office Haworth Cubicles. There are 2 versions: - Fits in between 2 panels - Fits on the end of a single panel edge. SCAD was used to create these and files are supplied. Enjoy! ... Update: (June 26 2018) Added a...
thingiverse
Over the door hook for a 45mm door thickness, Printed for my shower doors