over the cubicle hook 3d models
2704867 3d models found related to over the cubicle hook.thingiverse
Over the door hook for a 45mm door thickness, Printed for my shower doors
thingiverse
Took the original over-the-cubicle hook (#458166) and shrunk the clip size down to 6 cm to accommodate different cubicle walls. ... Print Settings Printer Brand: MakerBot ...
thingiverse
Remix of the original to make top that fits in the door jamb thinner for my door fit and also made the hook-loop slightly smaller.
thingiverse
A simple hook that you can clip on a vertical edge. ... Prints with no supports..
thingiverse
Simple door hook used for hanging aprons in my kitchen. ...You will want to lay it flat before slicing.
prusaprinters
Simple door hook used for hanging aprons in my kitchen. ...You will want to lay it flat before slicing.</p> Category: Household Supplies
thingiverse
... The easiest way I found to fix this was to adjust the scale. X should be 111.125, Y to 108.4426, and Z to 50.8 This works out so that the hook "opening" going over your door is 1 11/16" Have not tested yet and this is the first STL model I’ve made
thingiverse
One is that with the increased dimensions the part dows print over almost all of the y-axis, so be sure that your position is well calibrated. Also The support stuck into the 'M' on the backstop a little more intrusively this time and was a little...
thingiverse
Clip on cubicle coat hook for 2" x 5/8" cubicle trim. ...The .sldprt file is from Solidworks 2013.
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=983400 Instructions Using the following options: stem_height = 100 lip_thickness = 30 width = 2.5 lip_length = 36.2 hook_thickness = 30 lip_height = 36 hook_diameter = 30
thingiverse
I believe most people have 30-32mm door hook so the stl should work fine anyway. The "bumps" are to prevent slippage. But they only help when the door is closed. In the worst case scenario, anyway, when the fit is loose and load is heavy, you could...
thingiverse
This is a cublicle hook that will fit over a cubicle wall that is 2" in thickness.
myminifactory
A simple hook, attaches in the cubicle rails. ... Super strong--I use this to hold my backpack, messenger bag and even my coat in the winter.
cults3d
This is a double hook which can be plugged onto an office cubicles walls. The walls have a diameter of approx. 53mm. ...Printed in simple PLA
thingiverse
This is a double hook which can be plugged onto an office cubicles walls. The walls have a diameter of approx. 53mm. ... Printed in simple PLA
thingiverse
Original file Cubicle_hook_MatthewGTaylor.stl: Sturdy wall hook for Hayworth cubicle systems - locks into the track and supports a fair amount of weight. I use it for my backpack or coat. Check out @fiveseven808's [Cubicle hook (Steelcase...
thingiverse
... Instructions Print; cleanup; use! [2011-07-28] Added "cubical_hook_with_loop"; this has a hook at the bottom to hang the headphone cable on. ...[2012-08-02] Added "newcube_hook"; we have some new cubicles, so time for a new hook.
thingiverse
The hooks posted here are for 54 mm-wide (about 2 1/16") cubicle walls. ... Print Settings Printer: VERTEX K8400 Rafts: ...
thingiverse
Hook that fits office cubicle walls. Also, fits IKEA KURA bed rails. ...Print Settings Notes: In metric system.
thingiverse
... to MatthewGTaylor and fiveseven808 for the awesome base model! ... I've modified fiveseven808's design to work with the cubicles my office has. I found that fiveseven808's design was great, but the hooks needed to be moved back to fit the uprights.