oxygen tank wrench 3d models

Print Settings Printer: Flashforge Dreamer Rafts: No Supports: No Infill: 50% Notes: This Oxygen Tank Wrench goes under lots of torque pressure from the steel valve when being turned. I suggest making the infill 50% or more. I did 25% and it works...

Print Settings: Rafts: No  Supports: No  Infill: 50%  Notes: This Oxygen Tank Wrench goes under lots of torque pressure from the steel valve when being turned. I suggest making the infill 50% or more. I did 25% and it works good, but you can tell...

Wrenches, keys, and knobs for use with medical oxygen tanks or any tank with the same shut off mechanism. ... You can print the smaller ones and leave them on the tanks for a semi-permanent built-in shut off mechanism.

Oxygen wrench that fits on smashed tank valves. Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter ...

Oxygen tank wrench with a built in key holder. just glue your key in the back. ...non-circular keys.

Tools for opening and closing medical oxygen tanks or any tank with a similar mechanism.

Several designs of a shut-off valve for medicinal oxygen tanks or any tank with a similar mechanism. ...You can leave them attached to the tank for a semi-permanent shutoff mechanism.

I was asked to print an oxygen wrench and could only find one on the internet (http://www.thingiverse.com/thing:897996/), but I didn't like the design. I think it's a marvelous looking object, but I have my doubts about how well it will hold up over...

3D model of an oxygen tank

13 in OD, 55 in tall Oxygen tank

The designed tank which is been used in Hospitals for COPD patients

I much prefer knobs for situations like this so I modeled two that'll allow oxygen bottles to be opened with a knob instead of a wrench plus the room it takes up in a tank/bottle bag or backpack is much smaller. ... One model has "Oxygen Knob" embossed...

Instructions I created my design to hold on average about a 6 lb oxygen tank. The holder is cylindrical for the tank and then there is a flat piece on the back to make it more comfortable for the leg. ...The two “hooks” are very work in progress still...

Mycroft Holmes’ “personal supply of oxygen”

An Oxygen token for any project you may need it for. ... No Supports needed.

universe, I wanted to equip my character with an oxygen tank, allow him to enter toxicated areas for a brief amount of time. Long story short, real oxygen tanks are heavy and expensive. So I came up with a solution that gets rid of two problems at...

The Small Oxygen Tank asset from the space exploration videogame Astroneer. * The M4 FHCS and nuts are optional. * gray_coupling, red_outer_ring, and base_rib should be printed with "exclusive" slicing to ease assembly. There are options for...

This is a basic oxygen carrier I made for my grandma who could not afford to buy one since insurance didn't cover it. It may wobble a bit if put on an uneven surface, so there are optional side supports you can glue on to make it easier to keep...

Medical Oxygen Cylinder Dust Seal was trying to find STL, but had no luck.. so finally sketched it in Fusion360. Its works, but not perfect. ...May be someone could refine it...

Coupler for 2 E tanks. Side holes can be used to install additional tubes to carry / make a frame. ...

I tried to draw 30 m^3 oxygen tank

The gas tanks could supply the miners with oxygen for a couple hours, but were really heavy to carry around. This was one of the reasons why they were usually accompanied with a sling or like in this case with a box. The words on the back of the tank...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/a7sBBx9iPlA

Oxygen Tank 3D model.

Oxygen tank regulators require a simple wrench to open and close the valve. This wrench can do that and has some fail-safe redundancy in multiple slots. Useful for Fire / EMS or people who use home oxygen for respiratory therapy. I don't have an...

No description provided.

No description provided.

I haven't printed this but with supports it should print well.

Modelling: Solidworks 2012 Renderings: Keyshot 4 Thanks, CADMeIfYouCan Twitter: @CADMeIfYouCan Behance.Net: https://www.behance.net/cadmeifyoucan

Oxygen_Tank......................1236 polygon. ..............................................639 vertices.