packing tape holder 3d models
446388 3d models found related to packing tape holder.myminifactory
Pegboard holder for my packing tape dispenser. ...May not fit all dispensers, so check the measurements shown in photos against yours.
thingiverse
Loved the design of the 50mm packing tape dispenser, but them plastic teeth didn´t rip the tape, so i design this blade holder. The Blade is from the small 9mm Cardboard Cutters. ... If the blade is to lose, you can put a piece of paper between the...
thingiverse
1. ...Backpack holder on a tube. Max diameter 32mm 2. Backpack tape clip - 26 mm width. ...
thingiverse
This is a packing tape dispenser I designed to only use printed parts. Once the tape is dispensed, it can be cut with a box cutter or a pair of scissors, and the two pads keep the tape from sticking to the spool of tape, and keeps the dispensed tape...
thingiverse
I felt the need for a tape dispenser fot packing tape for a while, so in October 2019 i designed this. It prints in two parts. The dispenser body and the roll mount. The dispenser can be printed in any plastic, but i do recommend something a bit...
thingiverse
For all of you, who may have the same problem and don't believe in the chuck away society, and think keeping things functional as long as possible is a good idea, here you can save some time, if you have the same packing tape roller like me. The...
thingiverse
This came about due to my job reusing our packing tape tubes to store our product stickers on unitl ready for application. This will help contain the rolled up stickers from unwinding or falling on the floor rolling across our plant. This is a 7...
prusaprinters
Fits standard packing tape rolls and will fit rolls 120mm in diameter Takes 5 countersunk m3 bolts that self tap into the print. Glue the axle into the hub. Fill the cavity with something weighty. For the cutting edge I used a sharpened jigsaw blade...
thingiverse
Huge tape dispenser for 50mm tape reels. ...Reel inner diameter: 75mm Outer diameter up to 110mm The tabs might need some support material.
thingiverse
IMPORTANT NOTE: Rotate shield 90 degrees onto its side in your slicer so the grain of the filament layers will be perpendicular to the direction of bending when the shield is used on a tape dispenser. ...If you don't the piece is more likely to break.
cults3d
IMPORTANT NOTE: Rotate shield 90 degrees onto its side in your slicer so the grain of the filament layers will be perpendicular to the direction of bending when the shield is used on a tape dispenser. ...If you don't the piece is more likely to break.
thingiverse
50mm Tape dispenser. Designed to take 5 countersunk m3 bolts that should self tap into the print. 15-20mm bolts should do. Ive filled the cavity with gravel to make it weighty and stuck rubber to the bottom to make it grippy. The cutting...
thingiverse
A small piece to attach saw blade to the Packing tape dispenser to easily cut the tape without scissors or knife.
thingiverse
Simple tape holder / tape tree stand to keep your rolls of packing tape, masking tape, duct tape, and painters tape organized. ... IMPORTANT -- SCALE THE HEIGHT TO MATCH YOUR PRINTER -- on my PRUSA Mk3 I scaled the height, and only the height, to 37%...
thingiverse
Two inch packing tape dispenser Need 8 - 3mm screws 10mm long or glue and 3 - 3mm screws 10mm long. Need a hacksaw blade for a cutter. The cheaper the blade the better. The cheap blades can be drilled easier. To cut a hacksaw blade you can bend...
thingiverse
... Hence this thing, it converts an empty cardboard core from packing tape (ID about 76-77mm is pretty standard) into a spool for holding wire. The sides have a couple holes to hold the "inside" end and notches in the top edges to hold the loose end.
thingiverse
REMIX, but the original dont cut the tape... this version work great !!! ... enjoy.
thingiverse
time time time. ...on the right, and quickly made a little askew in a hurry and already prints;) some soft model. but enough that no one will throw. option to cut the tape does not work. I stick the scalpel to this and will be fine. ...print time 1:20h
thingiverse
I added a serrated edge to the main (right) body to cut tape. Model is printing now and I'll post photos and confirm if it works or not when it's done. ... You'll need to print the other parts from the original thing: ...
thingiverse
this is a tape holdet to put near your 3d printer so you can replace the painters tape easely