packout extension cord holder 3d models
365560 3d models found related to packout extension cord holder.thingiverse
Makes for quick easy removal off the packout with the cord still bunded up by removing tower. Spacing is approximately hand to elbow length so you can bundle on your arm and then clip towers on with the cord. Doesn't get in the way of opening or...
thingiverse
This attaches to the following Packout Tool Boxes: * Rolling Tool Box * Large Tool Box * Tool Box The image above shows a Carol Brand, Froghide Ultra Flex 50ft 12 gauge power cord. You can attach the brackets to the aluminum extrusion with #8 1/2...
cults3d
This will fit any aluminum Extrusion on a Milwaukee Packout as long as it's 51mm or 2 inches tall. Features: -All exterior edges are rounded. -Countersunk and threaded holes for two M5 × 0.8 mm x 10mm long socket head bolts. ...-The hole is the correct...
thingiverse
Milwaukee packout base rear hook extension cord hang with or without Milwaukee logo Added Dewalt version lol
cults3d
Holder for extension cord (europe plugs) that everyone can screw on table.
thingiverse
Just a simple extension cord cable holder mounted on wall. ...Need glue to stick.
thingiverse
Extension Cord Holder may need to be scaled up a bit to fit the size of the cord. ... also my first make so tips would help.
thingiverse
I found the best spool holder is an extension cord reel from your local hardware store. ... Remove the extension cord spool and hand crank, then print two filament spool holders. ... Simple and effective!
thingiverse
A lightweight wall holder for extension cords I made for my ancient kitchen. ... It's very slim, yet strong enough to hold up a 3 or 4 slot extension cord without any issues.
prusaprinters
Držák na zásuvky na stěnuDržák zásuvek na stůlUpevnění prodlužovačkyExtension cord holder
prusaprinters
I created this Extension Cord Holder to fix Extension Cord I used for lamp, charger and other electro devices. ...It consist from two parts which are fixed with 4 screws. </p><p>I printed them on my Prusa MK 2.5S from PLA with layer 0,35.</p>
thingiverse
Holder for AC extension cord under your desk - you can use glue os screws to hold it on place. easy to print - minimum supports needed it hold at place most of the EU cords which I found on the market. ... enjoy
thingiverse
This is a holder to be hanged from a radiator to house an extension cord. The inside is 48 mm wide, it could be made 50 because this one is pretty tight for a standard size used in Finland at least. ...Make it as long as you need, the model is 150 mm.
prusaprinters
If you want to bring a extension cord securely on a wall or a cealing, then print these two litle brackets and clamp the cord with it.easy to print, less material usage and no change to the extension cord it self
prusaprinters
Simple and fast printing USB extension cord holder. Done for this model of cable: https://www.amazon.es/gp/product/B071KWG5J6/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 It can be placed in any of the slots for a 30x30 profile. ...Align the nut...
thingiverse
Designed this to hold the device side of an USB extension cord. The USB plug is 25mm long, 9mm thick and 16.5mm wide. The bend protection is 4mm wide and the cable is 2.6mm wide. Maybe it fits other plugs, too. ... I use this to put my Logitech...
thingiverse
Needed to hang an extension cord on the back of a cart, so I cobbled up this thing. Instructions Took a while to print, and the last bit of the overhang that goes almost flat had a few problems, but...
thingiverse
Created to hold an expension cord to the side of my table while keeping it fully portable. ...This is the second version. The earlier version does not have a rubber band holder, but this is more practical albeit a bit less aesthetic.
thingiverse
Wall hanger for extension cables, to be held on the wall via screews. ...Big enough for 25m cable, see picture.
thingiverse
... ... Included a holder for the end connector of the cable instead of just letting it hang down on one of the sides, to make it easier to find it later. ... The screw holes have diameter 3.5 mm, countersink 90 degrees from 8 mm on top of the screw.
thingiverse
Didn't want to put any screws into the desk, so I took the idea from his holder to be hanged from an IKEA SMÅSTAD. The inside is 56mm wide with a small lip to sort of clip the block down. ...I mirrored it for the left and right, so I would have to use...
thingiverse
wanted to wall mount an extension cord. ...Purchased a bindmaster extension cord from amazon (B01N6XUCDY). ...for indoor use only.
thingiverse
This holder is design to snap on the Brennenstuhl extension cord/branch at a 45 degree angle behind my mega heavy stainless workbench. It will need to be adapted to your hardware and bench depending on your needs. But it might give you some ideas. ...
thingiverse
OBI Extension cord mount Optional mounts for more holding force. ... No support is needed.
thingiverse
I made this extension cord holder because i couldn´t find one i liked. So 20 minuts later in fusion 360 this is the result. The holes are 6mm and it fits if you use 5mm screw/bolts to mount it. ... No Support needed, but don´t go over .2 in layer...
cults3d
I made this extension cord holder because i couldn´t find one i liked. So 20 minuts later in fusion 360 this is the result. The holes are 6mm and it fits if you use 5mm screw/bolts to mount it. ... No Support needed, but don´t go over .2 in layer...
thingiverse
A bracket for hanging up a multi-way extension cord from Biltema https://www.biltema.no/bygg/elektro/grenkontakter/grenkontakt-jordet/grenkontakt-med-bryter-2000038281 Art.nr. ...46-3494
prusaprinters
OBI Extension cord mount Optional mounts for more holding force. No support is needed. Print Settings Rafts: No Supports: Doesn't Matter Resolution: 0.2 Infill: 100 Filament: generic PLA Category: Organization
thingiverse
The holder is designed to be low profile to not interfere with plugs. Dimension of 41x53mm is supported by default but the part can be scaled to support smaller or bigger sockets. You can scale and print the test piece to find the correct fit...