pcb stand 3d models

This PCB stand can stand up to 11 PCBs width 30mm length 115mm Height 12mm [17-09-22] v3 uploaded The width became 2 cm wider than v2. ... 12 PCBs can now be placed.

A tilted stand for a small PCB with a display

This is a little stand for PCBs. ... I needed a stand to hold PCBs upright while photographing them. I designed this to hold one PCB to be photographed while minimizing the visibility and impact of the stand within the picture.

Inspired by the amazing PCB Workstation (http://www.thingiverse.com/thing:801279) I used the PCB holder part and simplified the base for quick printing. Instead of the butterfly nuts I used this knob. Keep in mind, the short legs base can hold max.

Simple stand for your PCBs. Hold them off your table. ... Instructions Print at highest resolution of your printer - or else the top will snap off.

PCB stand with dimensions of 60x40mm. ... Protection from short circuit in the circuit.

PCB Stand offs for vertcial or horizontal PCB mounted - angled from the mount point., fits 3mm screws

The Fusion 360 file has some parameters to adjust the pcb size, stand thickness and screw size

A simpe open scad library to generate pcb stand offs. Three types can be generated Plain (round or hex) Retained Nut (round or hex) A Split Pillar, use a dab of hot glue or adhesive tape to hold it down.Edits v1.1 - made split_base slightly more...

Parametric pcb stand off hex

I made a 3mm 3.5mm and a 4mm stand off release tool, just simply slide the correct size onto your stand off and gently pull back on the PCB to free the PCB from the stand off, no more using pliers at awkward angles and trying to press the release in...

I left room between the PCB and the stand for through-hole pins and so a battery or other circuitry could be added, running the wires through the hole in the back. The test piece is available as well so you can make sure the posts line up correctly...

......http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: PCB_Thickness = 1.5 Inside_Diameter = 3 Clearance = 0.3 Base_Thickness = 1.5 Outside_Diameter = 8 Stand_Off_Type = plain Hexagon = true Length = 6

http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: Inside_Diameter = 3 Base_Thickness = 1.5 Clearance = 0.3 Stand_Off_Type = split_base Length = 10 Hexagon = false Outside_Diameter = 8...

......http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: PCB_Thickness = 1.5 Hexagon = true Outside_Diameter = 8 Length = 6 Clearance = 0.3 Base_Thickness = 1.5 Stand_Off_Type = plain Inside_Diameter = 3

......http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: Stand_Off_Type = plain Outside_Diameter = 8 Clearance = 0.3 Base_Thickness = 1.5 Length = 3 Inside_Diameter = 3 Hexagon = true PCB_Thickness = 1.5

http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: Hexagon = false Base_Thickness = 1.5 PCB_Thickness = 1.5 Outside_Diameter = 5 Length = 10 Clearance = 0.3 Stand_Off_Type = plain Inside_Diameter =...

http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: Stand_Off_Type = plain Inside_Diameter = 3 Base_Thickness = 1.5 Hexagon = true Outside_Diameter = 8 Clearance = 0.3 Length = 20 PCB_Thickness =...

http://www.thingiverse.com/apps/customizer/run?thing_id=79944 Instructions Using the following options: Clearance = 0.5 Outside_Diameter = 8 Base_Thickness = 0 Outside_Shape = 0 PCB_Thickness = 1.5 Stand_Off_Type = plain Length = 17 Inside_Diameter =...

http://www.thingiverse.com/apps/customizer/run?thing_id=79944 Instructions Using the following options: Base_Thickness = 1.5 Outside_Shape = 0 PCB_Thickness = 1.5 Stand_Off_Type = split_base Length = 10 Inside_Diameter = 3 Clearance = 0.3...

......http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: Base_Thickness = 1.5 Stand_Off_Type = plain Clearance = 0.3 Length = 7 Outside_Diameter = 8 PCB_Thickness = 1.5 Hexagon = true Inside_Diameter = 3

I designed this in fusion 360, I am doing a lot of PCB level repairs, especially on Xbox One. This helped me a lot to raise the PCB board from my workbench to prevent SMD component Damage. While I replace faulty SMD components.

A quick and dirty holder that grips a PCB board securely for soldering and other fine work. ...It's built around a 24mm M3 screw, a 10mm diameter magnet, and a 6mm diameter spring, but the included OpenSCAD file can be used to generate variations for...

A stand to hold you PCBs when you are not working with them. ... Printing: Not support needded, 0% infill, wall thicknes 1.2mm (or three wall lines of 0.4mm each).

This is a simple stand-off that can be used when adding additional modules or boards to something already created. The current height is 7mm The first one I uploaded is 7.5mm OD and 2.5mm ID to facilitate a 3mm threaded ID. It was also meant to...

Simple generic push fit nylon PCB stand off

3D Printing Stand for PCB, Arduino Mega 2560, LCD Nokia 5110, Keypad 4x4, STepper Motor Driver TB6600, Relay Module 4 ChannelFor model requests can call :WhatsApp / Telegram : +6281413274292

... stand itself. I also included different connection pieces. This is still WIP. Connectors are fine and require some force. The PCB holder on the other hand requires some teaking as it may break off some small capacitors required by the status LED.

... itself. I also included different connection pieces.</p><p>This is still WIP. Connectors are fine and require some force. The PCB holder on the other hand requires some tweaking as it may break off some small capacitors required by the status LED.

http://www.thingiverse.com/apps/customizer/run?thing_id=44894 Instructions Using the following options: Outside_Diameter = 8 Length = 15 Clearance = 0.3 Stand_Off_Type = plain Hexagon = false Inside_Diameter = 3 PCB_Thickness = 1.5 Base_Thickness =...