pegs and jokers 3d models
2292422 3d models found related to pegs and jokers.thingiverse
This is Pegs and Jokers board game that can accommodate 3-8 players, depending on how many pieces you print. Print as many game board pieces as there are players, then connect them in a circle. Print 5 pegs for each player. I had to use wooden...
thingiverse
3D printed pegs to go along with the boards located here: https://www.thingiverse.com/thing:1988720 I didn't want to fuss with going to get wood dowels and cut them down to use the peg toppers provided in the original post. Printed with PLA or...
thingiverse
Pegs and Jokers gameboard as prescribed at https://www.pagat.com/race/pegsandjokers.html Print as many of these as there are players, they hook together in a circle.
myminifactory
The design will facilitate from four to eight sections, and I've included the Autodesk Fusion 360 file "Pegs And Jokers V1.f3d" if you wish to customize the design. I 3D printed ""Board Section.stl" at .15mm layer height with 20% infill, and I 3D...
cults3d
The design will facilitate from four to eight sections, and I've included the Autodesk Fusion 360 file "Pegs And Jokers V1.f3d" if you wish to customize the design. I 3D printed ""Board Section.stl" at .15mm layer height with 20% infill, and I 3D...
thingiverse
Customized version of https://www.thingiverse.com/thing:2873982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2873982
thingiverse
Customized version of https://www.thingiverse.com/thing:1842869 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1842869
thingiverse
A take on Pegs and Jokers but using marbles. This board was designed to hold a basic 16mm marble and supports down to 3 player board configurations, and up to as many as you need. If anybody doesn't like the missing wedge in the corner when playing...
thingiverse
There is not a "standard Pegs & jokers" and this version and ruleset we call the California rules (Rules are included in pdf file). This set uses standard ~1/8 inch (~3.2mm) cribbage pegs that can be found on ebay and other sites. I show a...
cults3d
There is not a "standard Pegs & jokers" and this version and ruleset we call the California rules (Rules are included in pdf file). This set uses standard ~1/8 inch (~3.2mm) cribbage pegs that can be found on ebay and other sites. I show a...
thingiverse
I his is a case for my "travel Pegs & Jokers" https://www.thingiverse.com/thing:3061408 I print it both with brim as well as supports. I left enough room for storage of the pegs. I CA glued the slip-fit sections together. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:3061408 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3061408
thingiverse
Customized version of https://www.thingiverse.com/thing:3061408 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3061408
thingiverse
Customized version of https://www.thingiverse.com/thing:3061408 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3061408
thingiverse
Instructions Holes/pegs are 10mm, 8mm, 6mm, and 4mm diameters. Overall it is 45mm by 25 mm. The extra squareish area near the large peg is 15mm by 15mm. The holes are 5mm deep, and the pegs are 5mm high. I tried to make the dimensions as pleasant as...
thingiverse
Pegs are 2mm, 3mm, 4mm and 5mm. ...Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter ...
thingiverse
Peg to mount the spool holder on its arms if you don't have real bearings and the leadscrew. The central screw without the base to center your spool on the mount. Longer filament sensor holder for the sidewinder X1, aligning it to the extruder. ...
thingiverse
... during this COVID-19 pandemic. ...But, they can be used for anything you need to hang up while driving. There are six versions: In size, long, short, and micro. In style, pegs and hooks. I print on its side and with supports between the pegs/hooks.
cults3d
... during this COVID-19 pandemic. ...But, they can be used for anything you need to hang up while driving. There are six versions: In size, long, short, and micro. In style, pegs and hooks. I print on its side and with supports between the pegs/hooks.
thingiverse
Now the tortoise and hare can compete in a friendly cribbage game !
thingiverse
... and peg accessories for an even more impressive look! Requires: Thirty Eight Pegs and Peg accessories Super Glue, Krazy Glue or contact cement. ... For ideas on how to use this 3D printed item, visit: [stegoboard.com](https://stegoboard.com)
thingiverse
... Just to finish the project out I printed 2 boxes (same PLA, little infill, more layers) using Mark's Openscad hinged box library (https://github.com/sbambach/MarksEnclosureHelper), to make a box for cards and the mint tin for the lesser, lame pegs.
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=182621 Instructions Using the following options: step_percent = 15 Y_pegs = 2 X_pegs = 2 base_size = 100 peg_thickness = 2 peg_height = 20 step_width = 3 base_thickness = 0
thingiverse
This file includes Glowforge Bed pins, pegs, and a straight bar for holding unofficial Glowforge material to the bed.
thingiverse
The pegs are easy to handle for humans and robots alike. The board's holes allow just enough space to put the pegs easily while also securing them. ... Might be a great Tic-Tac-Toe version to play with younger children as the pieces are large and easy...
thingiverse
The pegs are 3mm square and come in a variety of lengths to allow for different ships to be mounted at different heights. This allows for a more dynamic looking fleet, and can help ships fit closer together when needed. I deliberaly chose a square...