pendant lamp cord 3d models
118481 3d models found related to pendant lamp cord.thingiverse
This is a recreation of the cord hanger that comes with IKEA HEMMA and SEKOND pendant lamp cord sets. ...Print Settings Infill: 100%
thingiverse
Pendant or weight to put on the end of the cord of a lamp with pull switch. The original one broke off, so I made a new one in the oval shape of the lamp. Its made out of two parts so that any knot in the cord wouldnt be visible. ...Pull your cord...
thingiverse
I bought some IKEA "Cord set SEKOND" For my Utility room http://www.ikea.com/gb/en/products/lighting/shades-bases/sekond-cord-set-red-textile-art-50263715/ Unfortunately I just have bare wires coming down from the ceiling, so there was no real way to...
prusaprinters
I bought some IKEA "Cord set SEKOND" For my Utility room http://www.ikea.com/gb/en/products/lighting/shades-bases/sekond-cord-set-red-textile-art-50263715/ Unfortunately I just have bare wires coming down from the ceiling, so there was no real way to...
prusaprinters
This is a low profile ceiling rose for pendant lamps similar to the one included in the IKEA HEMMA cord set. ...I like the practical design and cheap price of the Hemma ceiling light suspension, but the ceiling rose is far too big and bulky (height...
thingiverse
This is 3D printed a low profile ceiling rose for pendant lamps similar to the one included in the IKEA HEMMA cord set. I like the practical design and cheap price of the Hemma ceiling light suspension, but the ceiling rose is far too big and bulky...
cults3d
Clasp | Handy Pendant Light, Iphone Cord Dock, Power Switch Cover, Table Lamp in One
thingiverse
It's two part shell provides a cover for anything between the power point and the device cord hiding all the unsightly areas including the power point socket of the appliance cord. How to use Clasp: Print the two components. If you are using it...
myminifactory
It's two part shell provides a cover for anything between the power point and the device cord hiding all the unsightly areas including the power point socket of the appliance cord. How to use Clasp: -Print the two components. If you are using it as...
thingiverse
Lamp cord hook When it is nessessary to move a pendant lamp temporarily, e.g. if a table needs to be turned for a party. Standard the holes are 10 mm. Scale it to fit your cord + 1 mm. Print it as it is. Be sure that gaps are filled and the...
thingiverse
Use these clamps to secure a power cord to a floor lamp stand. Supported tube diameter: 16mm Approx. ...power cord cross section: 8mm x 4mm
thingiverse
This is a lamp cord shortener. ...Very handy for shortening a lamp cord which is too long. It is suitable for 8mm cables. ...Might work down to 6mm cables, but I haven't tried.
thingiverse
10mm Plug for lamp when cord is removed. I used Flex filament for this print. ...(Ninjatec Cheetah).
cults3d
We bought a new lamp, the cord needed to be more organized. ...Designed and printed these to solve the problem.
thingiverse
We bought a new lamp, the cord needed to be more organized. ...Designed and printed these to solve the problem.
thingiverse
Simple strain relief to protect cord on hanging lamps printed in ABS on Taz 6 with aerostruder
thingiverse
... ...(The later can be seen in the pictures alongside the printed version.) Can be used to hang a lamp or just a bulb by its cord in the ceiling or in a window. The design promotes a more straight up-and-down hanging of the cord than a simple flat hook.
thingiverse
Basic Lamp Cord or Wire Clips For Securing Wire. ...Designed in Sketchup to quickly solve a problem and wanted to share.
prusaprinters
Replacement cord clip for popular Ikea lamp with 12.8mm diameter post. ...Printed with PETG for better flex, 0.2mm layer, 0.4mm nozzle, 100% infill, 3 perimeters.</p>
prusaprinters
We bought a new lamp, the cord needed to be more organized. ...Designed and printed these to solve the problem.</p> <h3>Print instructions</h3><p>Category: Replacement Parts</p>
thingiverse
A simple hanger for a swag lamp cord. I made it to accommodate an approximately 6mm cord, but it may work for others. My print settings were unique, in that I already had a 1mm nozzle installed, so I just used that. For most, that will not be...
thingiverse
Can be used to shorten a lamp cord or to bind multiple extension cords together. Parameters can be changed to customize the size or number of slots as well as create multiple parts in order to speed up printing. ... Updated Ver.2 defaults to a...
prusaprinters
Lamp cord fastener if you have a plug above your windows and don't have any heel to attach the cord. ...My winter cabin have a wood strip around the house with holes above windows. Print instructionsInfill Lamp.stl 50% but you can experiment with this...
thingiverse
This is a remix of the Lamp Cord Shortener by jona0497-->https://www.thingiverse.com/thing:2684244/files I rounded it off and removed any sharp edges. Simply print upright with a little support. EDIT: There was a fault in the direction of the...
cgtrader
Cord Lamp by Design House Stockholm | 3d model produced by Design Connected | www.designconnected.com This 3d model is part of the highly acclaimed Design Connected collection featuring 6500+ carefully picked exclusive furnishings. Check out our full...
thingiverse
... adjust it for different diameters. For example: you have ∅6.5 mm cord, then you need to enlarge the model by 25% (6.5/5.2=1.25). The inner rounded surface is slightly angled for better cord holding. ...Use a clip as printed - glossy face downwards.
thingiverse
I use it with my lamp: http://www.thingiverse.com/thing:1020383 Print Settings Rafts: Yes Supports: No
thingiverse
A hanging lamp bracket for mounting from a shelf or overhanging edge. ...Pretty sturdy, but I have not tested the max load capacity with anything over 3kg.