pentax k1000 50mm lens cap 3d models
115114 3d models found related to pentax k1000 50mm lens cap.thingiverse
This is a replacement cap for the Pentax K1000 50mm kit lens.
thingiverse
This cap is for an older pentax 50mm 2.8f lens with no possibility to clip the cap inside. Please modify and fork as much as you want Instructions Printed with ABS on a echoRap V1. 0.2mm slices. ...15%...
thingiverse
A couple quick lens hood for the Pentax-M SMC 50mm 1.4/1.7 lenses, might work with similar lenses too. For mine it slides on and holds if you push firmly, although with different tolerences and lenses you might need to scale up or down slightly. I...
thingiverse
Pentax K Mount Lens Cap. Uses minimal plastic and time to make. ... Print settings: 0.00 - 9.00mm @ 0.1mm layer height 9.00 - 11.50mm @ 0.05mm layer height 11.50+mm @ 0.1mm layer height Takes about an hour to print.
thingiverse
Eyelet cover/dust cap for a Pentax K1000. ...You need one to avoid draining your meter battery Prints fine with tough resin.
thingiverse
This is a model of my PENTAX K1000 analog camera. ...Whish you enjoy it!
thingiverse
Replacement cover for the Pentax K1000 counter. ...Simple window, pops in, small notch (filled with paint) to locate frame number.
thingiverse
This is a grip for the Pentax K1000. You'll need a tripod screw to attach it. ...Supports on buildplate only.
thingiverse
Grip for Pentax K1000 35mm film camera. screws to the tripod mounthole on the base of the camera using a standard 1/4" tripod screw with finger grip. This example was created in ABS filament. ...If using this STL you will need to redrill the hole for...
thingiverse
I have several Pentax 67 lenses that don't have rear lens caps and I couldn't find any existing designs so I designed this one.
thingiverse
v1.1: added Pentax K Label on outside A rear lens cap for Pentax K mount. I bought a few vintage lenses which didn't come with one so I needed this. ... Included is the lens cap in STEP and STL formats for remixing and 3D Printing.
thingiverse
A very simple lens cap for a Pentax ME Super lens cover. ...Print Settings Printer Brand: MakerBot Printer: MakerBot...
thingiverse
Generic slip on to protect rear (bayonet) end of lens. ... TPU or Flexible filament work great, have not tested with PLA For Pentax 645 lenses and teleconverters
thingiverse
I needed a cap for one of my older Pentax 645 camera lenses and didn't want to buy a new one. This is something I came up instead of trying to copy Pentax's original design. Nothing special. Should fit all Pentax 645 series camera lenses. The blue...
thingiverse
Here's a rewind knob for the Pentax K1000. ...Not the best design, but it works.
thingiverse
This is an extended version of the lens cap for my AF35ML. ...The original lens cap keeps falling off since I have a filter attached with a slightly smaller external diameter than the camera lens. ... See comparison pics below
3docean
The 3D model was created on real base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...
thingiverse
Cap for lenses diameter 50(ish)mm Instructions You may have to re-scale it a bit depending on yours printer accuracy
cults3d
Pentax rear lens cap for K-mount lenses. Designed to fit more tightly than the Pentax caps, especially on 3rd party lenses. ... These caps are also about 20% shorter but wide enough to seal against the o-rings on weather resistant lenses.
myminifactory
Updated version of the Pentax rear lens cap, uses 1.75mm NinjaFlex as a gasket. ...The NinjaFlex protects the electrical contacts against dust and cleans them every time the cap is used.
thingiverse
Pentax rear lens cap for K-mount lenses. Designed to fit more tightly than the Pentax caps, especially on 3rd party lenses. These caps are also about 20% shorter but wide enough to seal against the o-rings on weather resistant lenses. ...
myminifactory
Pentax rear lens cap for K-mount lenses. Designed to fit more tightly than the Pentax caps, especially on 3rd party lenses. These caps are also about 20% shorter but wide enough to seal against the o-rings on weather resistant lenses. Instructions ...
youmagine
A lens cap holder for Pentax MX-1.I'm one of the lucky owners of this pretty cool camera in black. It is awesome but when it's time to take a shot, the lens cap is always in the middle as if it wanted to ruin all my photos every time!In terms of...
cults3d
A lens cap holder for Pentax MX-1. I'm one of the lucky owners of this pretty cool camera in black. It is awesome but when it's time to take a shot, the lens cap is always in the middle as if it wanted to ruin all my photos every time! In terms of...