peq 3d models
95 3d models found related to peq.thingiverse
Front sight that allows for forward use PEQ. ... It's a poor man's version of this https://railscales.us/leaf-peq?fbclid=IwAR1Lj-QK0GNIklEJSP9JVGpwI4YFeDcT5p-YQM5UTfucQ75tFqfZ_IdKvRE
3docean
The AN/PEQ-2 Target Pointer/Illuminator/Aiming Light (TPIAL) was a laser sight for use on rifles fitted with a Picatinny rail. ...It was manufactured by Insight Technology.
thingiverse
This is a combined remix of an old PEQ box design of mine, a PEQ box (actual) that I cannot remember where I got it, and some editing on old designs of mine. The internal dimensions of the holder is 100mm x 20mm x 50mm and on a picatinny rail. You...
cults3d
When you absolutely have to kill all the filthy aliens and other assorted galactic scum in your path, quietly. ...This is a sprue of 10 PEQ boxes/ Range Finders. ... Pre-supported .stl
thingiverse
This is a remixed of PEQ Box from paulodrugos you can find it her: https://www.thingiverse.com/thing:2098338 In this version, the dimensions of the ANPEQ are very big, so that it is compatible with all types of batteries, even gives the opportunity...
thingiverse
Just a simple PEQ case made for aesthetic purpose. The front is fixed with one M3x15 screw and nut. (the front also have another two screws just for alignment), the fixation in the picatinny rail is made with a M3x30 screw and nut. ...Print with suport...
thingiverse
I just remixed the PEQ Box from paulodrugos you can find it her: https://www.thingiverse.com/thing:2098338 In my version, I cut a small hole in the bottom, so you can lead the cables there and in the inside I cut a few things out and now there ist...
thingiverse
A PEQ-2 battery box made to fit a Titan 3000mAh 11.1v Nunchuck battery back. The rear cap is held on by M3 screws, 10mm and 20mm length but other lengths may be used. ... I am also finishing up a version integrated into G36 handguards.
myminifactory
Just a simple PEQ case made for aesthetic purpose. The front is fixed with one M3x15 screw and nut. ...(the front also have another two screws just for alignment), the fixation in the picatinny rail is made with a M3x30 screw and nut
thingiverse
I looked around and there was NO peq boxes out there, so i made one. Not the best looking but can fit a 2s 2200 mah battery, so if you run smaller batteries make a remix of a smaller version. Also fits kinda tight on the rail so might have to do a...
thingiverse
Yhis is my shotcounter, Peq mod. Did 2 pc. As it was made in sketchup, therefore i cant guarantee, that details will be without faults. Please check! Also i dont remember exactly what hardware i was used. :( Also added .skb :) ...
thingiverse
I made this in conjunction with my airsoft Peq battery box. I borrowed from Ohman74's IMF K Airsoft G36 Handguard, and his G36C "Spuhr R22"-like rail. Props to him. I only heavily modified his designs to make a more MG36 rail that I can run a battery...
thingiverse
... mount for your Mobius Scopecam. ... Code : HA3D-019 Model : An_Peq_Mobius Designer : Hornet Test done with Tianse PLA FOLLOW THIS PROJECT AND MANY OTHERS IN "HORNET AIRSOFT" YOUTUBE CHANNEL : https://www.youtube.com/channel/UCjG2fck4nwnPs5ap3ZqGF_w
thingiverse
If you prefer not having them dont print - else print and glue on (note that the covers fit both sides, so either way can be front or back, so if you dont like the PEQ addons, print two of the normal cover/lid) I left the back open so that internal...
thingiverse
PEQ/Battery Expansion designed for the new ASG CZ Scorpion AEG. ... Link to Compensator: https://www.thingiverse.com/thing:3922422 Link to Magazine Plate (mag pull): https://www.thingiverse.com/thing:3922417 Link to Tracer Cover:...
thingiverse
This is a deep remix or peq model from user "paulodrugos" on thingiverse (https://www.thingiverse.com/thing:2098338) I always wanted a peq box winch will fit my 11.1 battery - most models were just too small or just simple boxes. After gaining...
prusaprinters
This is a deep remix or peq model from user "paulodrugos" on thingiverse (https://www.thingiverse.com/thing:2098338) I always wanted a peq box winch will fit my 11.1 battery - most models were just too small or just simple boxes. After gaining...
prusaprinters
Internal dimensions: 194mm x 20.3mm x 20.3mm PEQ/Battery Expansion designed for the new ASG CZ Scorpion AEG. Link to Compensator: https://www.prusaprinters.org/prints/35236 Link to Magazine Plate (mag pull): https://www.prusaprinters.org/prints/35235...
thingiverse
fichier originale https://www.thingiverse.com/thing:2098338 je l'ai modifier pour qu'il puisse passer sur un rail picatinny en écartant un peu plus l'attache le reste fonctionne bien
thingiverse
These are the components needed to build an IR laser/illuminator. A build video will be posted on the Thrifty Operator YouTube channel. ... All parts are printed in PLA+ except for the button which should be printed in TPU.