pewter casting 3d models

My pewter designs thus far have been quickies and posted for the casting exercise rather than as presenting finished designs. Notice the mold halves were not clamped together for the pour. Instead they were cemented with some ABS cement. The...

Various heavy, cast decorative items are very often pewter. Zinc predominates in mass produced items. Pewter items are often stamped somewhere on the bottom with the word "Pewter". Metal suppliers sell ingots. My ingots weigh about 4 lbs each. Many...

Instructions This post is a continuation of my original attempts to cast metal in ABS molds. http://www.thingiverse.com/thing:286521 The design began life as a torus (in Blender), twisted around with the Simple Deform modifier. It looked nice but...

Once the plaster stops heating in the microwave you should be good to go for metal casting since the microwave will drive off the water and solidify the plaster. NOTE: Failure to fully dry the plaster part could cause a steam explosion. Google it,...

I added some sprue/vent structures into the design to allow casting in pewter. I experimented with several different casting mold and sprue structures and found that this seemed to work best. Since this is a one-sided piece (back side is flat), I...

pewter, metal

14.04.2020 Made a v2 with shorter side walls on the overlapping parts :-) Made a 2 part casting flask to use with my pewter casting. This can be printed in PLA, PETG or ABS. This has rings indented on the inside to help the clay/sand to stay in...

Scan of a decorative pewter cup from Germany

Pewter Bowl from the shipwrech of HMS Invincible 1744

Small pitcher imitation pewter body + handle Happy May Day

Casting

Casting

Casting

Casting

Casting

Here, I've modeled a pewter teapot that used to be my mothers (see photo). And here I've learned that SW does not like to loft profiles made from splines- it can really screw them up. ...I wanted to make this pot look more hand-made, but this is still...

Casting assembly

SAND CASTING

Cast component

A component from casting

DISEÑO Y MAQUINADO CASTING MASTERCAM X

This is a casting model for small type pipes with round and rectangular flange.

High-quality 3d model of a Pewter Jug

My entry to GDC Beer bust challenge , nothing fancy just a good old pewter beer stein ;)

A model of a pewter tankard with minimal etching design, ideal for a medieval tavern scene. ...Renders done with 2 subdivision levels.

Pewter porringer on soil pedestal Location: Fredricks site (31Or231), Orange County, North Carolina. Period: Historic (AD 1700). Material: pewter. Dimensions: length, 22.5 cm; width, 19.3 cm (soil pedestal only). Notes: Catalog no. 2351a555, North...

Pewter pipe stem Location: Fredricks site (31Or231), Orange County, North Carolina. Period: Historic (AD 1700). Material: pewter. Dimensions: height, 193.0 mm; diameter, 17.9 mm. Notes: Catalog no. 2351a2260, North Carolina Archaeological Collection,...

RK17 A00033 is a pewter tankard found during the archaeological excavation of the Rooswijk in 2017. In 2016 Dutch and British archaeologists undertook a survey on the site of the Dutch East Indiaman Rooswijk which showed it was at high risk. To...

RK17 A00033 is a pewter tankard found during the archaeological excavation of the Rooswijk in 2017. In 2017 and 2018, the shipwreck of the Rooswijk, a 300 year old Dutch East India Company (VOC) ship which sank on the treacherous Goodwin Sands in...

RK17 A00027 is a pewter jug found during the archaeological excavation of the Rooswijk in 2017. In 2017 and 2018, the shipwreck of the Rooswijk, a 300 year old Dutch East India Company (VOC) ship which sank on the treacherous Goodwin Sands in January...