ph probe stand 3d models

The PH probe and his controller, these are the good measures taken from the SEN0169 that you can recover on the web.

Atlas Scientific pH-probe

This pH probe will fit 100s of models/brands of Aquarium Computers, Aquarium Controllers, pH Monitors and pH Controllers; both dual and standalone types.

I use a pH probe for stability testing, unfortunately the manufacturer doesn't sell any holders for it and as it isn't held upright the storage solution can run dry, causing the probe to become damaged. ...I designed this to overcome this issue.

Made this thing to wash the the Ph probe in a water treatment plant with air or water. ... Please feel free If you like this model and you want to support my work that I am making, you can donate me if you want with paypal: http://paypal.me/SeanManagh ...

At work I needed something to hold a pH probe off the bottom of the container while calibrating and came up with this. It fits a Rosemount 396P perfectly (1" MNPT) but may work for others. Co-workers requesting I print more... Not sure how to...

Aquarium holder for Hydromet PH probe. ...Suitable for glass thickness of 8 mm

This is a 2 probe holder, It works with a 11mm pH probe and a 12mm EC probe. Both bought in DFRobot webstore. ...Print Settings Printer Brand: RepRap ...

This is a holder for an Atlas Scientific pH Probe ( or other appropriately sized probes) and a Waterproof DS18B20 Temperature sensor, which suctions to the side of an aquarium. Having these two sensors together allows for temperature compensated pH...

Simple 3d printed probe holder for reef tank. ...Holes are sized for 1/2'' diameter probes and the magnet slot is sized for a plastic coated magnet 1" x 1/2" x 1/4" thick.

Fake 12mm Probe to insert in your poolsystem in winter or while you take the real probe out for calibrating or replacing. It avoids air sucked into the system or water spilling out. ...

Replacement for the Suction Cup Holder (which regularly lets the Probe drops into the water). ...Fits all Diameters of 13-14 mm and Glases of 12mm thickness or less.

Shrouding to guard the pH probe against bumps and drops with mount for easy fitting. ...Protecting this rather fragile device.

Hi. ...This is my first project. This is holder for Weipro Ph meter probe. ...(tank with rims) Created in https://www.tinkercad.com

Looking for a stand to hold your Apera PH tester? ...Tested with the PH60.

Small stand for 5 pieces of PH paper for the lab

Small stand for 5 boxes of PH fix-sticks from Macherey-Nagel

This is a pH meter stand that can be helpfull with generic pH meter for Arduino. ... Hardware needed: - 3/8 threaded rod, 2 x 3/8 bolt ,and 3/8 split washer - 5/16 nut and bot - 2 x M3 nut and screws

The lab I work in was obtaining some portable pH meters and I did not want them to lie around and risk getting damaged, so I modeled this holder which fits a 1 cm test-tube (size may vary) inside and can hold the portable pH meter. ... I used the lab's...

The lab I work in was obtaining some portable pH meters and I did not want them to lie around and risk getting damaged, so I modeled this holder which fits a 1 cm test-tube (size may vary) inside and can hold the portable pH meter. I used the lab's...

Flat stand for Essential Phone PH-1

Simple Holder for a PH Probe (unknown chinese Brand, 13mm diameter). ... Will fit to the edge of the Bioflow filter (tested on Rio with Bioflow M, also fits on Bioflow S) to hold the PH Probe just above water level.

Milwuakee MW101 Stand. ... If you want, use a screw 3.5x12 to fix the dish to the stand

code: https://github.com/frossty/Ph_Temp_Prob Tools: PH probe with BNC converter: https://www.aliexpress.com/item/32957428276.html?spm=a2g0s.9042311.0.0.142a4c4dEZFU4D ESP8266:...

... grip. ;D Also print it with higher numbers of outside perimeters, to get 100% infill/stronger print. Outside probe diameter: 19.30mm Peg diameter for silicone sucker: 4.5-5.5mm Suckers: http://alishort.com/5Jw5c Probe: http://alishort.com/YoV7C

https://heidolph-instruments.com/en/products/Magnetic-Stirrers~c18#Models It allows the probe to be lowered deeply and to measure the ph e.g. directly in the bottle. Additional parts: 8mm aluminum tube (approx. 1m) e.g. from OBI or Leroy-Merlin...

oscilloscope probe stand, fit nice with probe head, but not perfect for cables

Stand to hold Cobra Probes secure in a wind tunnel.

A height adjustable stand for two cobra probes. ...Provided scale is 1:600.