phantom 2 landing gear upgrade 3d models
1025135 3d models found related to phantom 2 landing gear upgrade.pinshape
Simple and easy to Print Landing Gear for Phantom 2 and Phantom 2 + Drone.
thingiverse
Set of parts to use with 6mm carbon tube that allow to fold the landing gear for transport. No screws, no glue - just slide, turn and fold. Good idea to use it with Zenmuse quicklock adapter. You can adjust the height by cutting carbon tubes...
thingiverse
Increases the height of the DJI Phantom legs to accommodate a gimbal and goPro. Remix of http://www.thingiverse.com/thing:475349. This one is slightly taller than the original, and has a rounded reinforced tab area to help prevent the tabs from...
thingiverse
Landing gears that are further back in the front to avoid recording them while using a GoPro
thingiverse
Designed in collaboration with https://www.bustmold.com/locations/ottawa/ and https://www.bustmold.com/locations/montreal/ Check out the video of Dji Phantom landing with new 3d printed landing gear - http://www.youtube.com/watch?v=NWIRmrVGtgA...
thingiverse
... GEAR, prevent your gimbal to hit the ground. ...Idea for easy to attached and detached as need. Fit with Phantom2, Vision and Vision+. Also will fit with Phantom one but you will need to apply DJI Phantom Pad (DJI-PHVLGPAD) on snap landing gear.
cults3d
I need make more strong landing gear on EPP RC plane. ...this is IT.
thingiverse
DJI PHANTOM clone landing gear Print Settings Printer Brand: RepRap Printer: RepRap Kossel Rafts: Yes Supports: Yes Standards CCSS Overview and Background Lesson Plan and Activity Materials Needed
thingiverse
Legs for Phantom 4 Pro. ...Best result if use Nylon and print one by one. Temperature: Bed - 110, Hot-end 265, No fun, in box 50. You need 2 left and 2 right and 2 basic! Original legs - 38g, this from nylon - 29g. ...
thingiverse
Customizable landing gears for your Phantom 2, standard, vision or plus. Consider the print settings below for sufficient stability! Depending on the camera and gimbal you want to use, the standard gears may be too short. If you don't want to...
thingiverse
The design is remixed from arod24's thingiverse.com/thing:475349 gear for Phantom 2 (mine is for Phantom 1). I have changed the clamps so that the extender doesn't need help to hold on to the stock gear of Phantom 1 anymore and fits pretty snugly. It...
thingiverse
Landing gear extension kit to raise the height of your DJI Phantom. For use with fort example Gimball. Holes are for M3 screws. Kit d'extension pour augmenter la hauteur du train d'atterrissage de votre DJI Phantom. Pour une utilisation avec par...
thingiverse
Stock landing gear is 42grams, Low Skid landing gear re-printed with less material is 28grams Added new leg design which is only 4g leg1holo.stl Now working on Long version so a Gopro and Gimble can be used. ... Indoor test...
thingiverse
Clip on landing gear stabilizers which extend to base of your Drone for more stability.
thingiverse
Self-designed landing gear. The goal was to be screw-free and quick to replace. ...The elements simply slide into each other and hold each other.
thingiverse
... clearance.to keep it off the ground. A lot of the others I have seen raise it too high or stand out too much. I like the simple clean design of the phantom and want to not stray from that too much and when printed in white these blend right in.
thingiverse
... Printed on an Ender3 using 80% infill PLA. Printed sideways with supports to allow the layer lines to go lengthwise, to give better strength when clipping on and off the landing gear. Adds rigidity to the gear. ...
thingiverse
These fit fairly snuggly if you put them on while the foam pads are still on the original gear. They seem to wiggle a bit on mine, so either scale down very slightly and do as I did and use some hot glue to hold them in place. I put a few rubber...
grabcad
Rear landing gearAnd front landing gear in its box with doors.All of them have simple suspensions.
thingiverse
Avoid cutting your Bixler 2 by using this holder. ...It can be attached with rubber bands or glued in place.
thingiverse
I wanted this kind of landing extension for my quadrocopter, but the one I found was too long for my purpose. So here it is: Exactly your size! ...Please share your makes with me.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=878057 Instructions Using the following options: shift = 0.5 outer_r = 4.5 gap = 1 Thickness = 10 inner_r = 2 Wall_Thickness = 2 additional_height = 20
thingiverse
This is a 5 cm version of our famous BUSTMOLD LEGS upgrade for stock Dji Phantom landing gear. With V5 of BUSTMOLD LEGS you reduce the weight by at least 30 grams and it becomes super stable. Its great when you want to fly your phantom "naked",...
thingiverse
This is a 9 cm version of our famous BUSTMOLD LEGS upgrade for stock Dji Phantom landing gear. With V3 of BUSTMOLD LEGS you get the same height as original landing gear but much less weight (at least 20 grams less). Extremely easy to print and...
thingiverse
This is a 12 cm version of our famous BUSTMOLD LEGS upgrade for stock Dji Phantom landing gear. With V3 of BUSTMOLD LEGS you get the same height as original landing gear but much less weight (at least 20 grams less). Extremely easy to print and...
thingiverse
Enhanced version of the drone Phantom II landing gear. Slightly taller and wider which prevents the clash of gimbal with the ground during landing. Also prevents right leg to appear in the image captured by go pro, which could happen in some...
myminifactory
Enhanced version of the drone Phantom II landing gear. Slightly taller and wider which prevents the clash of gimbal with the ground during landing.Also prevents right leg to appear in the image captured by go pro, which could happen in some...
thingiverse
So, to use our Phantom 3 landing extensions you will need the following: 2- H5 labs landing gear extensions (this design) 1- http://www.thingiverse.com/thing:909566 (P3 Gimbal Guard to go) 4- 4-40 x 1/2" long screws 4- 4-40 nuts Please reference the...