phantom adapter 3d models
119434 3d models found related to phantom adapter.thingiverse
This adapter allows you to connect a Walkera Gimbal G-2D to a DJI Phantom 1 or F40 without any modification to the gimbal or the Phantom. ...With this mount no leg extensions are needed.
thingiverse
This adapter will allow you to use an Angel threaded feedneck (such as the Automag ULE feedneck shown) on a CCI Phantom. This may also work with other feednecks, but this has not been tested. The threads are not modeled in this design, so the...
thingiverse
This is a remix of my Automag to CCI Phantom feedneck adapter. ...It has been modeled with the 7/8"-20 UN threads commonly used with CCM feednecks.
thingiverse
This is a remix of my Automag to CCI Phantom feedneck adapter. ...It has been modeled with the 13/16"-32 UN threads commonly used with Empire feednecks.
thingiverse
A quick and dirty remix for the CCI Phantom Feedneck Adapter by PhantomJM that uses the stock screw as the original design was too short to use the stock screw.
thingiverse
Hey. ... this is the walkera 2g adapter to phantom 2 . ... The distance of the screws is not perfect, but it can be adjusted.
thingiverse
This is an adapter to fit a 140mm fan in the 200mm slot in the top of the NZXT Phantom Case. ...I was unable to find a 200mm fan that would fit the top of the case so I created and printed this adapter.
thingiverse
This is an adapter to fit over the Phantom 4 battery and hook up to a 12v Hotor Car Vacuum. If you are field charging your batteries then a critical step is cooling them down after you take them out of the P4P. Using this adapter and the Hotor 12v...
thingiverse
Got dust in your motors? ...This adapter is designed for the Armor All 2.5 Gallon wet/dry vacuum, and works best printed in NinjaFlex. No supports needed. ...Fits the 2312 motors.
cults3d
Got dust in your motors? ...This adapter is designed for the Armor All 2.5 Gallon wet/dry vacuum, and works best printed in NinjaFlex. No supports needed. ... Fits the 2312 motors.
thingiverse
Adapter for the old ND filters to fit on the newer Phantom 4.
thingiverse
DJI Phantom 3 Lens Adapter for Nerf Terrascout. ... Designed to allow lag in the terrascout camera system to be reduced As seen in [this youtube video](https://youtu.be/1h9pwFWiSZA)
thingiverse
I bought a Tab A 7 (2016 model) for my Phantom 3 Standard but It was just slightly too big to fit in the device clamp. So I made this adapter and it seems to work okay. I will be revising it to make it about 1mm longer as it is a pretty tight fit.
pinshape
Summary DJI Phantom Remote Controller parabolic antenna adapter Because I'm looking ahead when pilot my Phantom, it's easy to increase distance adding parabolic background to antenna. Print and put to the inner side sticky aluminium or cuprum foil......
thingiverse
DJI Phantom Remote Controller parabolic antenna adapter Because I'm looking ahead when pilot my Phantom, it's easy to increase distance adding parabolic background to antenna. Print and put to the inner side sticky aluminium or cuprum foil... ...:) ...
thingiverse
A 3D printed adapter for Cooler Master MF200 fans to be installed in the OG NZXT Phantom. Printed in PLA with 100% infill. ... Not perfect, required some massaging to get all 4 holes to line up, luckily the MF200 is a bit flexible.
thingiverse
Flying your Phantom over water, are you crazy?! Perhaps rabbit... I've had this idea in my head since the lab got the drone and when I finally sat down to model it it took very little time. PLEASE NOTE: This model assumes you have already purchased...
thingiverse
Sma mount for raplacement of 5.8g antenna of phantom 3 standard, this adapter allows to mount a sma Antenna on top of the controller. ...Print Settings Printer Brand: MakerBot ...
thingiverse
This is a prop balancer adapter pair (CW and CCW) for the DJI Phantom 2 self-tightening nuts to Dubro Prop Balancer. I printed it out of Nylon and it works amazingly well. Adapts from the 6x1mm Metric Threads to the 3mm Dubro Balancing rod...
thingiverse
Enjoy the adapter to attach your nexus 7 tablet on DJI phantom 3 Standard. The clamp that comes with the bird does not support nexus 7, so I remixed bipedal's nexus 7 mount to attach to the phantom 3 remote. ...
thingiverse
... parts and click it on! ... HDMI adapter link: https://www.tethertools.com/product/tetherpro-hdmi-mini-swivel-adapter/ https://www.banggood.com/360-Degree-Rotation-Swivel-HDMI-Male-to-HDMI-Female-Adjustable-Adapter-Converter-p-996627.html?rmmds=search
thingiverse
Zenmuse H3-3D Gimbal SJCAM adapter (based on SJ5000+) The cable can be made by removing the USB connector from gopro hero3 USB cable supplied with the gimbal and soldering the SJCAM/XIAOMI micro USB to AV cable instead (2nd photo). Adapter should be...
prusaprinters
Zenmuse H3-3D Gimbal SJCAM adapter (based on SJ5000+) The cable can be made by removing the USB connector from gopro hero3 USB cable supplied with the gimbal and soldering the SJCAM/XIAOMI micro USB to AV cable instead (2nd photo). Adapter should be...
pinshape
Summary Hi, This is one of my older accessories for DJI FC40. This thing is useful when you want to use GoPro 3 (or 4?) as FC40 camera. Only pull out damping rubber and put it to this holder. Enjoy! Btw. ...on the image you can see original model form...
thingiverse
Hi, This is one of my older accessories for DJI FC40. This thing is useful when you want to use GoPro 3 (or 4?) as FC40 camera and supress jello effect. Only pull out damping rubber and put it to this holder. Enjoy! Btw. on the image you can see...
thingiverse
*Work in Progress Designed for the iFlight Naked GoPro Hero 8. Recommended printing with PETG as TPU is too flexible. ...This offers a simple solution, but vibrations can get into the video since there is no dampening.
pinshape
This is one of my older accessories for DJI FC40. This thing is useful when you want to use GoPro 3 (or 4?) as FC40 camera and supress jello effect. Only pull out damping rubber and put it to this holder. ... Enjoy!