phat dac 3d models

A model of the phat DAC for use in your designs. ...Hope it helps.

Screw-Free PHAT DAC Case for Raspberry Pi Things ;-)

SoaPiBarZero - a soap bar shaped enclosure for the Raspberry Pi Zero. ... This version is a case for any Raspberry Pi Zero with a pHat Dac.

Using Raspberry Zero W - 802.11 b/g/n wireless LAN - Bluetooth 4.1 - Bluetooth Low Energy (BLE) Pimoroni pHAT DAC witb Dual RCA Jack (https://www.adafruit.com/product/3016) - 24-bit audio at 192KHz - Line out stereo jack - pHAT format board - Uses...

- - - - - This is an enclosure that just fits [Pimoroni Phat Dac](https://shop.pimoroni.com/products/phat-dac) available at [@Adafruit](https://www.adafruit.com/product/3016) attached on a Raspberry Pi Zero W with the included GPIO header. The lid...

Update 8/24/2017: Added a version with SD card access hole as per the feedback (PhatDacSD.stl). This is an enclosure that just fits Pimoroni Phat Dac available at @Adafruit attached on a Raspberry Pi Zero W with the included GPIO header. The lid can...

[rpi-audio-receiver](https://github.com/nicokaiser/rpi-audio-receiver) [PI Bluetooth Audio Receiver](https://docs.google.com/document/d/12cK4heNd7kY3jYZI_sW1AD407dn_ds-9zZdX4qs-TJg/edit) [Pimoroni pHAT DAC for Raspberry Pi...

Case for Raspberry Pi Zero W made in 3mm acrylic to contain the pHat DAC of Pimorini. It has a button to turn off the Raspberry Pi that must be connected to pin 5 (for example) and to ground. If you use the Volumio player, you can load the plugin...

<p>I redesigned ywabiko's enclosure with wider tolerances. The Raspi assembly should be easier to slide in.</p> <p>While I was at it, I used my favourite vent pattern and moved it from the sides to the front and back to shorten printing time.</p>...

I redesigned [ywabiko's enclosure](https://www.thingiverse.com/thing:2417798) with wider tolerances. The Raspi assembly should be easier to slide in. ... While I was at it, I used my favourite vent pattern and moved it from the sides to the front and...

Simple remix to support my DAC Using incredible audio DAC by JustBoom for Raspberry Pi Zero https://www.justboom.co/ Im using volumio in hotspot mode, https://volumio.org/ Makes an incredible capable small device that can play high definition digital...

basic DAC

pHAT badge holder. ... A RPi Zero (W) can also be placed on the back of the badge, connected to the pHAT. Tested with a number of pHATs. ... Screw together with nylon M3 x 8mm screws and nuts.

This is a inside joke, the Phat Bee. Observe those glorious bee thighs. ...worship them.

Just a model of the explorer Phat. Included unpopulated PCB model, 2x20 female pin header, 1x20 pin header and assembled PCB. For use in your own designs. ...Hopefully, it saves you some time.

portable DAC

This is a portable DAC.

Customized version of http://www.thingiverse.com/thing:739573 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=739573

Carga axial y radial

3D printable drone attached container

CARGA AXIAL Y RADIAL

This is the box for the PCM5102DAC from Aliexpress and used here: https://sites.google.com/site/orangepizero/home/orangepi-one/dac-i2s This is an I2S DAC. DAC is working quite fine... In case you have no I2S access, you can use USB Amanero or Chinese...

Real time rendering for a DAC (numeric/analogic converter) designed by myself. ...Materials made in Substance Painter

... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=751540 Instructions Using the following options: line5 = La multi ani! line4 = DAC 665 T line3 = DAC 665 line2 = D A C line1 = DAC

This is my first attempt in making an enclosure for my music streamer. ... The box in mainly made for Raspberry pi 3 b+ with the Allo Boss 1.2 I2S DAC converter, but it could work for other Pis and DACs. ...

Rough model of a Hifiberry DAC+. The dimensions are accurate as possible with a cheap chinese calliper. ...I needed a simple model to design a laser cut case for my Raspberry Pi, for that kind of work, the precision is good enough.Modeled with Fusion...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=751540 Instructions Using the following options: line5 = OBIECTIV line4 = MIHAELA LETA line3 = DIESEL line2 = R O M A N line1 = DAC 6135

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: inner_margin_width = 1 font_outline_style = rounded whichextruder = monochrome minimal_color_layer_thickness = 0.6 lug_style = plate...

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: lug_width = 5 border_width = 0 lug_style = plate font_name = Lobster glyph_coalesce = 25 textextruder = extruder2 font_with_style =...

dropped and lost a couple buttons while i was making a Gameboy Macro Phat, so modeled these replacements from another Phat i had on hand. There are ever so slightly taller (0.1-.2mm) than the originals as that works better for the casing I use on my...