phone bike holder 3d models
380158 3d models found related to phone bike holder.thingiverse
Simple Bike Holder for 6-inch smartphones like Xiaomi mi9t and etc. ... For assembly you are gona need: 1x m4 10mm 2x m4 nut 1x m4 20mm
thingiverse
I use an app on the phone as a bike computer, so this holds the phone firmly in place and allows me to see some info live. The lower section is for a battery pack, so that I can leave the screen on all the time. You won't be able to use this as...
thingiverse
Simple but effective design for an Iphone SE and iPhone 8 holder on a Qwic MN380 bike. Easy to install and stays firm in place even on a rough road. ... the larger iPhone 10 also fits
thingiverse
Simple holder for phone. ...Not tested, will print tomorrow. For me it is important to have thick enough holder to keep phone without taking out from case. ... You will need 2 8mm rods/alloy pipes and spring or rubbers to build holding force.
thingiverse
... would put it out there for fun. The Holder is attached to the bike frame with zip-ties. I created a duct-tape "net" by folding a piece of duct-tape in half and then attaching it to the sides of the holder. ...Feel free to comment and ask questions.
thingiverse
Easy to print and mount with rubber on your bike. ... More fill give more stronger construction.
thingiverse
Designed to be used as GoPro holder or Smartphone holder.To use as GoPro holder just remove upper plate (Smart phone holder) and you are ready :) It works for Huawei Y5II (143.8 x 72 x 8.9 mm) + silicone case, adjust it to your needs. Best is to...
thingiverse
This is a phone holder and charger for bike. Tested over 700km on https://www.gbi-event.org/en/events/gbi-europe-2018.html During large trips more than 8 hours I need a holder and charger to follow the route track by gps. I use...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=614516 Instructions Using the following options: Phone_Thickness = 12 Phone_Length = 151 Handle_Bar_Diameter = 26 Phone_Width = 82 Holder_Height = 17
thingiverse
If you have an other phone please login to Onshape, Make a copy and upload your remix for your phone. ...https://cad.onshape.com/documents/544537d5588df7bd1e20fbea/w/c4a53947feff5069f84ebc5e/e/06736afd53122e52454adbb6 If you have any ideas to improve,...
thingiverse
Phone or navigation holder for bike or motorcycle with 22 mm bar. ...M6 hardware.
thingiverse
Bike phone holder for Xiaomi Redmi 3 in case. You can easily change its scale to make it fit your phone. ...
pinshape
Easy Phone and Cup Holder fro any Bike. ... Free Support Model Easy to use with PLA, ABS, PET or Flexible Filaments
thingiverse
This is bike phone holder from two things; - Handle Bar Mount from "Modular Bicycle Dashboard" https://www.thingiverse.com/thing:29860, - M5 nut, knob, bolt, and clamps from "Modular Mounting System" https://www.thingiverse.com/thing:2194278 STL...
thingiverse
A quick Phone Holder for the Handlebar of the Peleton Fitness Bike. Mounted with 4 M3 Screws, Washer and Nut. Designed to be wide enough for an iPhone 12 Pro Max. ... Printed with supports underneath the Arc
thingiverse
This is a phone holder to put on your bike. The width of the holder is based on my iPhone 8 + case, but feel free to change the width to match your phone. Instructions --- Just follow the instructions, attach all parts, and lock everything with...
thingiverse
A simple training bike phone holder. Must fit on a standard training bike (if not, just enlarge the circle). Diameter : 36mm. ... V1 : more straight, less large (smaller flange) V2 : more oblique, more large (bigger flange) No raft, no support,...
thingiverse
This is a phone holder for bike. While it is freely inspired by some existing design, I made this one because I only print PLA, and wanted a sturdier design than what exist on this website. I already used it for a few hundred kilometers and had...
thingiverse
Simple Rogue Echo Bike phone holder. Two sizes, one is 160 mm inside the other 170. Depth is 13mm for both. Print it flat on the bed. ... Edit: added new desing for the 170mm and it is a bit deeper where goes the phone.
thingiverse
A simple training bike phone holder. Must fit on a standard training bike (if not, just enlarge the circle). Diameter : 36mm. ... You'll need a printing surface of 200x200mm minimum V1 : more straight, less large (smaller flange) V2 : more...
thingiverse
I designed this phone holder to fit my road bike and my phone, trying to keep it somewhat aero. I added suspension to the clips in order to lessen the vibrations in the phone. The phone mount is in multiple pieces, so that no supports are needed. A...
prusaprinters
The Fusion file is parameterized to easily adapt the dimensions to other mobile phones and bikes (Modify > Change Parameters > Favorites). Print instructions Prusa i3 mk3+ Layer Height: 0.15 mm Satin Spring Steel Sheet Filament: PETG The...
cults3d
It is a phone holder to be fixed on the handlebars of his bike. For a Galaxy S9 and a D26 handlebar You will also need 4 M4 nuts and bolts to secure the assembly. ... Leave me a message for other phone, I will complete with a new file (put the...
thingiverse
Existing bike phone clamps are good, but they leave the phone open and exposed to the elements. I wanted to re-use my Karrimor iphone arm case on the bike. Phone stays in it's usual case, pop it into the waterproof case, strap to platform. Platform...
thingiverse
Printed this to mount my phone to my bike stem while indoor riding. I wouldn't use it on the road as I haven't really tested it for durability, but works great for Zwifting. 2 flavors, Pixel2 with pretty slim case and Iphone 11 pro with apple leather...
prusaprinters
I designed this phone holder to fit my road bike and my phone, trying to keep it somewhat aero. I added suspension to the clips in order to lessen the vibrations in the phone. The phone mount is in multiple pieces, so that no supports are needed. A...
thingiverse
This is a phone mountign for your Bike. Due to the individuality of bikes, specially the handles shape, you might need to rework it a littlebit, but that should be easy in Fusion360 for example. The mounting is made specifically for the Samsung...