phone camera cover 3d models
283172 3d models found related to phone camera cover.thingiverse
I'm not paranoid but the Internet is a scary place. ... You can easily flip it over to use the camera if you put it in with tape. This is for the Samsung A53 but you can make one for your phone in seconds
thingiverse
well it's what it says ;) It fits at least on Iphone 4s,6 and SE.
thingiverse
I spent too much time designing this cell phone camera cover, but I got fed up with the existing products constantly falling short. ... This cell phone cover is designed to: * Not rip off * Not snag on lint * Not have slider pop out * Not slide open...
thingiverse
This is a phone case for the Pixel 3a with slide covers for the front and rear camera. The case is intended to be printed out of TPU and the front cover and slides out of PLA or other rigid filament. The phone will not fit if the case is printed with...
thingiverse
========= ======= ======= A friend asked me if I could replace the camera lens cover in their tablet. There are plenty of these on eBay, and I found a 10 mm lens cover that fit the tablet. You probably don't need a tool to install one of these,...
thingiverse
Camera cover to laptop. Hole diameter-7mm. It is to laptops with monitor diameter 6-8mm. ...
thingiverse
It is camera cover to laptop with monitor diameter 6-8mm. Diameter hole-7mm. ...
thingiverse
Camera Cover Layer thickness: 0.2mm Line width: 0.3mm Infill: 100% Print speed: 10mm/s
thingiverse
This is a camera cover that slides open and shut. ...You will need to glue it to your computer and make sure it slides well before glued.
thingiverse
Made this low profile camera cover. Based on the Lenovo W540. ...Print Settings Printer Brand: MakerBot Printer: ...
cults3d
Cover your camera with the nice protecting hand Just print the part Use double side tape to stick it on the back of your laptop screen Enjoy
thingiverse
Cover that fits in between the lens and body of my Nikon N65 camera (though will probably work for others), used for long exposure photography in places with passing cars, stray light sources, etc... Depending on your print, you may want to paint...
thingiverse
This is a camera cover i designed and printed for my laptop (DELL vostro 15-7580) It lets you see the LED that indicates if the camera is active or not and allows you to hide the lens to be sure no one is spying on you ;)
thingiverse
Small camera cover to be glued on with fixing tape. The dimensions are rather accurate if your printer is not very precise I recommend a small blow of sandpaper to remove quarter of a millimeter too much. ... Take your usual printing parameters,...
cults3d
This is the Huawei P20 Phone cover. ...If you want to 3d print this then this is the whole assembly you only have to separate the parts and start printing.
thingiverse
This holder keeps your phone steady when you can't hold it by yourself. Max. angle for phone is ~20 degrees. ... Holder is designed for OnePlus5 with covers.
thingiverse
I modified it so it would allow me to mount my phone to this camera mount - https://www.thingiverse.com/thing:2490356 My phone is actually an Android phone (not an iPhone), but the mount works fine for me. ...
thingiverse
A generic phone holder which connects to any camera stand with the standard 1/4-20 threaded screw. No need to tap the hole - just print and use. ... Use one or more rubber bands to secure the phone.
myminifactory
just a prototype of phone holder for recordink, timelapses ect. ...has possibility to hold phone in 2 angles, depends on direction where the camera points DESIGNED TO BE PRINT IN ONE PIECE! ...without any supporting material
thingiverse
... securely under the tension of 2 rubber bands. Users seem to be able to use it without instruction. It can be set up to hold the phone facing down as a doc cam, or also swivel up to be a conferencing camera. It securely holds most phones. ...