phone camera stand 3d models
290157 3d models found related to phone camera stand.thingiverse
Use the camera holder from a selfie stick as a tabletop phone/camera stand. ... Reuse the screw from the holder and add one m4 nut and a small m3 screw (+/-10mm).
thingiverse
Here is my phone camera stand. The stand is made so it enables rotation in two direction. Only non printable parts are 16mm M3 screw with nut and rubber band. I used PLA. The Part 1 (the base) was printed at 70mm/s 15% infill 0.2 resolution and 3...
thingiverse
This is a addon to this great Phone Camera Stand. I've made it and it's awesome, but with PLA, there can be a little stress to the locking on the rotating part, where both part_4 are attached. So I've made this little lock to put underneat it,...
thingiverse
A generic phone holder which connects to any camera stand with the standard 1/4-20 threaded screw. No need to tap the hole - just print and use. ... Use one or more rubber bands to secure the phone.
thingiverse
This is an attempt to build a 3D printable camera stand cell phones. The design is by Greg Lord (http://www.gplord.com/) who was hired by New York Public Library for the Performing Arts as part of an "Innovation Project" Ideally, these parts will...
prusaprinters
A generic phone holder which connects to any camera stand with the standard 1/4-20 threaded screw. No need to tap the hole - just print and use. ...Use one or more rubber bands to secure the phone. Print instructionsCategory: Camera Print Settings...
myminifactory
For those moments when you need to take a group photo, but there is no one around to take the photo for you, and no where to prop up your phone. Print at 0.2mm layer height.
cults3d
For those moments when you need to take a group photo, but there is no one around to take the photo for you, and no where to prop up your phone.
grabcad
A 3D printable camera stand for a generic smartphone. ...Designed to be as small and simple as possible.
myminifactory
just a prototype of phone holder for recordink, timelapses ect. ...has possibility to hold phone in 2 angles, depends on direction where the camera points DESIGNED TO BE PRINT IN ONE PIECE! ...without any supporting material
thingiverse
English: This is a Phone Mount attachment to the Camera Tripod made by Kemel770. I tested it with Samsung Galaxys10e and Smasung J3 2016. Should work with any phone of similar size Link to his Project: https://www.thingiverse.com/thing:1460181...
grabcad
sometimes we want to use our cell phones as a camera , so i have built one , it can move from point to point without moving from its position , its really useful and cheep and i am happy to share it with you .- you just want PVC pipes * email :...
thingiverse
Hello Tribe, Don't forget to hit that like button Please enjoy this cell phone stand it was designed to be used with a Camera stand. ... Here is our Sunlu Affiliate link https://www.sunlu.com/?sca_ref=507104.Qc1O4Eu3lJ Visit us on...
prusaprinters
Hello Tribe, Don't forget to hit that like button Please enjoy this cell phone stand it was designed to be used with a Camera stand. Here is our Sunlu Affiliate link https://www.sunlu.com/?sca\_ref=507104.Qc1O4Eu3lJ Visit us on...
cults3d
Adjustable camera / smart phone stand - fits all phones up to a thickness of 10 mm including iPhone 4-5, Galaxy Nexus, Galaxy Note. The stand ball joint allows for adjustable tilt and (some) roll. Excellent for time lapse photography, stop motion...
youmagine
A simple camera/phone stand that is customisable to suit any action camera or phone. It has: * 20 roll positions in landscape and portrait through a full 360deg at 11.25deg steps * 20 pitch positions in portrait through a full 360deg at 11.25deg...
thingiverse
Adjustable camera / smart phone stand - fits all phones up to a thickness of 10 mm including iPhone 4-5, Galaxy Nexus, Galaxy Note. The stand ball joint allows for adjustable tilt and (some) roll. Excellent for time lapse photography, stop motion...
cults3d
Also we used a standard ball head (see more here: https://amzn.to/2PyvXQP ) to mount on top a duck foot mount to hold the phone / camera. Major Favor: if you make one of these please post the Make and share it with the community :-) . Don't...
myminifactory
Also we used a standard ball head (see more here: https://amzn.to/2PyvXQP ) to mount on top a duck foot mount to hold the phone / camera. Don't forget our YouTube channel here: http://YouTube.DIY3DTech.com as if you want to see what we are up to...
thingiverse
Also we used a standard ball head (see more here: https://amzn.to/2PyvXQP ) to mount on top a duck foot mount to hold the phone / camera. **Major Favor:** if you make one of these please post the Make and share it with the community :-) . ...
thingiverse
This is a redesign of the Camera Phone Stand by blincoln that I redesigned to better fit my Pixel XL in an otter case. You will need the original stand from blincoln and then add this as the upper and lower holder. ... This will require supports to...
pinshape
... or screws in the design but there are open holes to allow the assembler to determine the best setup for them. There is also a built in function that allows the phones/cameras to detach from the unit and stand alone due to retractable legs.
thingiverse
I designed this camera/phone stand to help me film my projects, the design is fairly heavy duty and meant to fit with the threading on my olympus camera while at the same time is collapsible and can become fairly compact. To assemble it you'll need...
thingiverse
My phone has a large camera bump and this stand accounts for that using a cutout however the dimensions used will work for lots of different devices. ... printed on a prusa mini not MK3s just there is no option for mini on thingiverse for some reason.
thingiverse
This design is a remix of the "Mic Boom Arm Phone/Camera Holder Clamp" from KeyboardPrinter: https://www.thingiverse.com/thing:5232897 The original is a fully printed phone stand for microphone arm. I like the strong hold on the phone, the...
thingiverse
I haven't tried it yet, and I am concerned the phone is too big to work when not laying horizontal when making Periscope videos. I'll report back when I test it. The dimensions are for the phone only, and don't include my case. I'll break out the...
thingiverse
This is my first publicly shared design so I hope others find it useful. I wanted an easy to print tripod to hold my Nexus 4 whilst taking close up pictures, so I ended up designing one in Tinkercad. The final design ended up having four legs...
thingiverse
After trying to get the original to work and failing (it is an ingenious but fragile design), I decided to recycle the parts I had printed into something which I knew would work. The joints require 2x M5 nuts and bolts. You need to print 2x each...
prusaprinters
Aprroximately a 3 hours print.Upgrade your quick clamp with infinite possibilities with that universal phone, tablet and camera stand:Hold your phone on a waiting room arm chair;Hold your phone while recording a print;Hold your phone hidden under...
thingiverse
Stand for mobile phone. Allows you to install it on a flat surface or attach it to the edge of the table (shelf). This system allows you to combine parts as you like, getting the necessary functionality. ... Bed Phone Mount: 2 x tube dia 14mm, length:...