phone holder for honda crv 3d models
2437355 3d models found related to phone holder for honda crv.thingiverse
This is a cell phone holder for a Samsung Note 8 and a 2020 Honda CRV EX-L. With a phone in the holder it does block the hazard light switch but removing the phone gives you access to the switch. It also allows air from the vents to get to the phone...
thingiverse
This is a cup holder that sits in the standard CRV cup holder and provides a base for larger cups or mugs. This holds the cup up so the other cup holder is useable. Updates still to come. ... [Big Macs also fit - version with fry holder coming]
thingiverse
This is a mobile phone holder designed specifically to fit into the Honda CRV cup holders. It includes holes for threading a USB charging cable into the base. I've printed it successfully using both PLA and ABS. Some supports will be needed, but...
myminifactory
A handy removable change holder that fits nicely into the compartment under the armrest of a Honda CRV mk4.
thingiverse
My CamelBak Forge drink bottle did not fit in the cup holders of my Honda CRV 2006, leading to it wobbling about all over the place and falling out. This print inserts into the original cup holder in the centre console. This can be printed in...
thingiverse
Caution, the gear shifter is not usable when the holder is in place I use this holder for longer drives. The base was printed at 20% infill to retain some flexibility for the clips The post was printed at 50% and trimmed with a Dremel tool once the...
thingiverse
Replacement hubcap for my Honda CRV How I Designed This Designed to print using aquasolve support for the indent and Honda logo on the front (underside of print). Use silver filament for the print. Keep an eye on the print while doing the support,...
thingiverse
Needed a phone mount for a 2019 Honda CRV and my OnePlus 7 Pro. Commercial options were $80+, and this was clearly a financial situation a 3D printer could solve. 5, 10, and 15 degree standoffs are included for custom viewing angles. Designing a...
thingiverse
2002-06 Honda CRV has a poor cup holder design that causes drinks to tip over during a turn. ...This attachment fills in the empty space to hold drinks in place.
prusaprinters
These are cup holder inserts/ adaptors for a 1st gen CRV. Should be printed in ABS but PLA prototypes has held up well so far.No supports needed The taller one can have its outer diameter reduced by roughly 1mm for it to fit better next to...
thingiverse
This is a simple print to give you a couple extra places to hang your shopping bags for Honda CRV Second generation (2002–2006). It prints without support - I used PLA. Just take the headrest on the back seats out and it will slide over the metal...
thingiverse
... on my 2000 model it does. The inside of the adapter is tapered to hug your precious beverage cup. It is designed specifically for the "grande" size of a certain arguably overpriced coffee house, but will work fine for other sizes and brands as well.
thingiverse
The Wiper Fluid Cap on my 2000 Honda CRV finally cracked and fell off, so I used the freeware version of eMachineShop to design a replacement. The Wiper Fluid Cap has a center hole in it so you can zip tie it to the long plastic piece that slides...
thingiverse
Simple remix of this hanger to fit a 3rd generation Honda CR-V (may fit other vehicles). ... Please tip the original designer and understand all safety concerns (use at your own risk).
thingiverse
This is designed to replace the factory switch blanks in the dash of a 2002-2006 Honda CRV, for the purposes of mounting an auxiliary switch for things like light bars, fans, etc. ...This is a flat blank which will mount flush with the dash in flat...
thingiverse
This is a phone holder for Honda ADV-150. It is placed on the speedometer cap. ...It needs to be combined with a phone clamp in the market.
thingiverse
Recently, I purchased a 2018 Honda CRV but hated both available mounts, so I designed my own in Fusion 360. I was learning Fusion 360 at the same time which is why there are two design methods (split and All-In-One). ... The second AIO design has a...
thingiverse
You also end up fussing with cables, or using wireless charging which not all phones have, is slow, heats your phone up a lot, and doesn't work for android auto. This is a one handed, drop it in and its connected over USB with no effort. This...
grabcad
This is a collaboration of information I have gathered on the internet as well as a physical study. ...it is a lift spacer for Honda crvs 1 generation
thingiverse
Frame to adapt 6-inch speaker for honda CRV 2008-2011
thingiverse
Pieza adaptador tapa para surtidor limpia faros Honda CRV
thingiverse
Car (2006 Honda CRV) had a dummy mount for XM, and the factory antenna is not made any more. This fits a Sirius XM SV300 antenna, and bolts directly to the holes in the roof of the car. ...Uses M4 bolts and screws into the plastic.