phone mount for tacoma 3d models
2396582 3d models found related to phone mount for tacoma.thingiverse
iPhone 12 pro max used in picture Used 3M Super-Strength Molding Tape, 03614, 1/2 in x 15 ft for sticking the mount to the car (might need to be modified for different adhesives) phone clamp from junkyard but probably can get one from amazon...
thingiverse
This is a 17mm ball mount designed to fit onto the center of the dashboard on a 3rd generation Toyota Tacoma, above- or next to the infotainment screen. It requires some double sided tape to install and is best printed in PETG or some other heat...
thingiverse
I wanted a phone holder for my 1997-2004 Tacoma that would allow me to stick on the magnet that came with my phone case: https://smile.amazon.com/gp/product/B08G8CTXBS I also wanted it to replace the screw for the Oh Sh*t handle on the driver side,...
thingiverse
There are 4 different options to choose from: - Flat with Cable Management - Flat without Cable Management - 10 degree tilt with Cable Management - 10 degree tilt without Cable Management This is the phone magnet mount I used:...
thingiverse
I've been trying to find a good place to store my phone in my Tacoma. The cup holders are always in use and the charging pad area is usually full of stuff and isn't a convenient location. I remixed two ideas together to come up with this solution. It...
thingiverse
I used a Wizgear magnetic phone mount, removed the tape from the mount and used epoxy instead. I'm sure the tape could still be used instead of epoxy, I just wanted better heat resistance. The mount was designed around a 10-24 machine screw and nut...
thingiverse
Simple design to mount phone in tacoma 3rd gen. Just use 3m "extreme" double side tape to stick magnet mount linked below. The phone case I am using (linked below also) has metal infused into it so there is no need for the classic metal plates most...
thingiverse
I designed this to interface with a generic phone holder instead of using the mounting mechanism that came with it. I recommend printing this with PETG or ABS at a high infill and using multiple outer walls with the print. Also, please note that...
prusaprinters
I also superglued the 3mm nuts to the support plate, since you cant install the dash with the mounting plate installed. Parts -2ea - M3 x 8mm bolts2ea - M3 nuts1ea - RAM Mounts Ball Adapter with 1/4" - 20" Female Threaded Hole and Hex Post...
thingiverse
VanTrue dashcam mount for the Toyota Tacoma GoPro windshield mount.
thingiverse
This is for mounting a Tekonsha 90195 P3 trailer brake controller into a 3rd gen Toyota Tacoma. ... This requires removal of the pocket to the left of the steering wheel and screws into the panel in place of it.
thingiverse
Probably fits other Aukey dashcams, too. ... I took jdebriyn's design and moved the tab on the top to fit the mount to the camera better. Also, I tried this print in PLA and it did not stand up to the summer heat. ... Try PETG or ABS
thingiverse
Phone Holder for 2018 Toyota Tacoma (Fits in vents & on top dash) Printed in PETG for temp. ...resistance, parts all printed separately Phone charger hole in bottom of housing, chamfer on bottom face of both large parts for ez removal
thingiverse
plate to mount hopkins insight brake controller in a 3rd gen tacoma. ...replaces useless cubby on left of steering wheel.
thingiverse
(https://www.amazon.com/dp/B01F0NJ56G/ref=cm_sw_r_tw_dp_zeGDxbT6S5EP2) Version 1.6 for better fit to Togaurd, Also covers light escaping from front of camera mount. ...Print Settings Printer: Folger Tech Kossel 2020 ...
thingiverse
... much cleaner looking install that allows you to also remove the whole unit quicker. NOTE: The photos of the gray model are of Version 1, Version 2 should produce a more flush mount for the screen as I forgot to account for the ethernet plug depth.
thingiverse
You can also wire it into your overhead console for power using this mini-USB kit from Amazon (https://www.amazon.com/dp/B00MH4ZVHO) following this writeup...
thingiverse
...... I created this UV5R Radio mount for my 2010 Toyota Tacoma TRD Off-Road. I printed it face down without any issues. It is designed to be used with the belt clip provided with your radio. I added 3M automotive mounting tape to the back of the mount.
thingiverse
This is a simple dash mount I remixed to hold a backup camera screen for my RV, it would also work well as a phone mount with a magnet mount.
thingiverse
Wasn't able to find an elegant solution to mount the slim radios. ...The thicker android radios using the double din standard work fine with the OEM mounts with the tabs bent back, but this is for the slimmer radios as pictured.
thingiverse
Could be modeled tighter but good as it is. ...Print in ABS since PLA will sag in hot weather.
thingiverse
I combined qwiktunes Echo Auto Mount Base with Cracked1's phone mount to make something that would work for a 2018 Tacoma. ... I've glued 2 8x3mm neodymium magnets into it and it works great so far.
cults3d
I combined qwiktunes Echo Auto Mount Base with Cracked1's phone mount to make something that would work for a 2018 Tacoma. ... I've glued 2 8x3mm neodymium magnets into it and it works great so far.
thingiverse
this toolbox is made to fit snug into the Tacoma truck at regulars scale and is held on by 2 body clips and then 2 screws inside the box to the bed of the truck, somewhat waterproof if you make a gasket with liquid electrical tape or a rubber band...
thingiverse
Vled rear mount for 3rd gen toyota tacoma Print two, squares on top are for a zip tie to keep the cable down. I recommend ABS. (I did PLA, we shall see how long it lasts.) I still used the 3m for the light. I also used 3m for adhesion to the vent....
thingiverse
An iPad mini mount for the front cupholder in a 3rd gen Toyota Tacoma. This replaces the OEM middle divider part. The bracket is sized to fit an iPad mini 4 in landscape. I might build a larger size for an iPad if there is enough space. ...If requested,...