phone telescope 3d models
60498 3d models found related to phone telescope.prusaprinters
I designed this adapter for a friend that always had problems to hold the phone steady to take pictures through the telescope lense. ...The adapter is designed in a way that it can be used for different phones, so if you switch your phone you do not...
cults3d
Joining everything with a bridle and a bar of 1 cm in diameter and measure that you require, you already have a support for your cell phone attachable to your telescope. I hope it helps you or gives you an idea. Hi, hope this helps you... By...
thingiverse
The parts should precisely adjusted with telescope and phone installed, with help of camera, and then glued together. I used slow hardening glues to give me plenty of time for corrections. ...Adjusting is complex, even a slightest offset matters.
youmagine
It can easily be modified to fit other eyepieces for either microscopes, binoculars, or telescopes.The base piece fits tightly on the phone.I sliced in Cura with 25% infill, no brim, no raft, 0.25mm layers, support material...
thingiverse
This was designed to fit my phone and tablet, so it has a depth of .5 inches, and has an extension range from 6 inches to 11 inches. I plan to use electrical tape as a rubbery surface to help keep the devices in with friction, as they can slip out...
thingiverse
Here is a nifty little phone adapter to take photos with your phone while it is hooked up to your telescope.
prusaprinters
Both phone and eyepiece have a tight fit so that nothing moves during use.Tested on an iPhone 12 mini with the official leather case, on top of a National Geographic AZ 60/700 refractor telescope.Zooming the camera to 2x allows the whole camera area...
thingiverse
Supports are needed while printing only for the Clamp.stl Screw / Nuts / Washers: - 2x 12mm M3 screw (for clamp) - 2x M3 nut - 4x 10mm M4 screw (3x for phone holder, 1x for nut under "star" ) - 1x 12mm M4 screw - 5x 9mm M4 washer - 1x 12mm M4 washer...
thingiverse
So I saw this piece of software which was available for my phone that as long as the telescope is parallel to the telescope tube it will basically act as a PUSH-TO system by telling you to point you scope left, right, up , or down to center on the...
thingiverse
Phone holder for Celestron Firstscope. ... Seek sky objects by stellarium, google sky map...
thingiverse
Edit it online https://www.tinkercad.com/things/0qnCzpKazqP When I attempt to take a photo of what I am seeing through my telescope with my smartphone, it is very difficult to have my phone perfectly aligned with the eyepiece. This proves especially...
thingiverse
The phone mount is made for an Alcatel One Touch in case and will need to be scaled to your phone. For a 10" telescope I needed 10 bands and 8 connectors. The connectors will allow you to slide the bands through and size for any size telescope. ...The...
thingiverse
I created this so we could take picture with a mobile phone.
thingiverse
I designed this holder to mount my Galaxy s3 to my 6" Newtonian telescope. Using a "bubble level" app, I securely centered the holder using two strips of velcro. Now using the SKeye app, or the astronomy app of your choice, makes finding &...
thingiverse
this is a model for making a refracting telescope with a smart phone. The project was done during a weekend at the Nasa Apps Challenge 2014 in Montreal. The design is calculated for the available lens that we got at an optometrist shop nearby. The...
thingiverse
A simple telescoping phone stand for videos or time lapses that is fully 3D printed. Made up of 3 tubes the slide together, and get you a large range of motion, with 3 degrees of freedom. For best, and speedy results, use a rough layer height for...
thingiverse
The Right Grip has an opening to attach a Mayflash Magic-NS adapter (https://mayflash.com) to connect the JoyCons to my Android phone as JoyCons aren't fully supported in certain apps without rooting the phone. Use Switch Pro mode on the adapter. ...I...
youmagine
So I measured the dimensions of the phone in its case, the location of the camera lens, and the diameter of the eyepiece on my binoculars.Though an STL is provided, it is unlikely to be a match to your phone and binoculars/telescope. ...Download the...
thingiverse
It works fine with my "First Scope" telescope and on the pictures with Celestron 9mm Wide Angle Eyepiece - the default lenses that came with this scope would probably need modification to the clip to fit over the focuser. for assembly: 6x M3 bolts...
thingiverse
This is custom design for mobile phones with a specific kind of telescopic stand attached to the back of them (see pictures). The stand slides into this holder, which in turn can be slid into the CD slot of your car. ... If you want to see what...
thingiverse
Needed a cell phone holder for my telescope to make it easier to view through the eyepiece. My current phone is a HTC One M8 with an Otterbox case. The phone holder is a perfect fit with the otter box. the eyepiece holder is a touch loose currently.
thingiverse
This Open SCAD file will generate a smartphone mount adapter for connecting your smart phone to a telescope or microscope. The default parameters in the Open SCAD file are for an iphone 4G with a protective case. ... Enjoy!
prusaprinters
I took a quick look but didn't find any pre made as these two devices usually don't require any interchangeability. This adapts sizes from 23.2mm (common microscope diameter) to 1.25" (this is the most common/standard telescope eyepiece...
thingiverse
This is an adapter for mounting your phone to a 3.6cm (1.42 in) outer diameter telescope eyepiece. It works very well with most common eyepieces greatly simplifying the astrophotography process. Enjoy! I've seen a good way to use this: just buy or...
thingiverse
I made a remix of the mount to fit my Skywatcher 150/750 but it should fit on any telescope that has the same focuser (or the same 2 to 1.25 inch adapter) since it clamps around that part. There is also a reducer that can be used to clamp the mount...
thingiverse
This thing allows you to mount a laser pointer up to about 25mm diameter on a cell phone or tablet running Google SkyMap or Skeye, and then to mount that to a telescope, binoculars, a tripod, or a handle. It allows for precise alignment of the laser...
thingiverse
A customizable microscope and/or telescope to phone adapter. Configure the cross's height, width, and how far up the cross to print the horizontal (to e.g., not interfere with your phone's volume buttons) to fit your phone. ... Uses the holders and...
prusaprinters
Just a little helper object to hold my phone when doing daytime polar alignment. Previously, I held it by hand and the camera bump made it difficult to keep flat while adjusting the mount. STL is sized for a Pixel 3a XL. Fusion source...