phone tripod 3d models
65651 3d models found related to phone tripod.thingiverse
This is a easy to print, assemble and use phone tripod. Part list: 4x 20mm M3 screws and nuts 2x foam and glue 1x rubber band Printer settings don't matter too much. ...Note that I have a cheap printer, you can get way better results with a...
myminifactory
This is a easy to print, assemble and use phone tripod. Part list: 4x 20mm M3 screws and nuts2x foam and glue1x rubber band Printer settings don't matter too much. ...Note that I have a cheap printer, you can get way better results with a decent...
prusaprinters
A simple phone tripod for photography.Notes: Use 3 perimeters for the Base.stl. ...The others are fine with 2.Orientate the parts correctly to avoid need for support (the default position is not correct for a few parts...apologies)BOM4 x M3x18mm...
thingiverse
Simple phone tripod. I chose to use metal hardware- all 1/4-20 threads - but printed 1/4 fasteners could be used, too. ... --- ### Filament ##### Checkout the black filament used...
youmagine
"Iphone6tripod.stl" will accept phones sized 65mm - 70mm (iphone 6/6s/7, galaxy s4, htc one, blackberry z10, nexus 4/5). "Iphone5tripod.stl" will accept phones sized 59mm - 64mm (iphone 4/5/5s/se). if you have a case make sure to measure. only tested...
thingiverse
- Use a screwdriver to slightly widen the gap of the Tripod Base ball joint and push the phone clamp in place. - Side the M5 bolt through the printed screw. If it's difficult to get the last bit of the bolt head seated, use an M5 nut on the other...
prusaprinters
A ball jointed printable tripod.Measure the width of your phone (or google for its specs), and select the closest size Phone Clamp. If you use a phone case or something, make sure to use the total width including the case.Print (at least) the Phone...
thingiverse
A tripod for your phone so you can take videos or long exposition pictures. There are 2 different legs, short/long. There are also 2 different holders. One uses m3 screws/bolts and you will have to print the stops so the hardware does not...
thingiverse
Check @Electro_Dreams out here: https://www.instagram.com/electro_dreams/?hl=pt I also have this tripod changed for the GoPro cameras, just check my profile and you will find it. As always if you have any opinion about my creations and possible...
cults3d
Just another universal phone tripod mount with 1/4-20 thread. The uploaded .stl files are relative to an improved version. ...Enjoy it.
thingiverse
Just another universal phone tripod mount with 1/4-20 thread. The uploaded .stl files are relative to an improved version. Enjoy it. ...Print Settings Printer: Geeetech G2S Pro ...
cults3d
Folding mobile phone tripod with tilt adjustment. Fixing the legs to the body using 1.75 mm filament after counter drilling the joints to 2 mm. ... Articulation using an M5 x 20 screw and an M5 nut.
thingiverse
I remixed three phone holder. ... Tripod Folding Version 2 https://www.thingiverse.com/thing:2813597 Tripod Phone Stand https://www.thingiverse.com/thing:4694593 Modular Mounting System https://www.thingiverse.com/thing:2194278
thingiverse
Phone tripod holder. Modular: just print more ball joints to create longer legs. The only thing you need to add (optionally) is a rubber band to secure the phone. Relatively parametric: the OpenSCAD files are included. The dimensions can be...
thingiverse
This is a simple phone tripod. All the parts are printable. Printing: All the parts has been designed so that no support is needed and post processing is very easy. Check the HowToPrint image inside the zip folder for the proper printing...
prusaprinters
I was looking for a phone tripod stand and there was nothing usable for a case with a popsocket so I remixed this. ...(Make sure your popsocket is centered on your phone for it to stay level, it won't work if mounted near the edge.) I used a few...
myminifactory
... that won't creep (PETG or ABS, not PLA). Printer:-- Eustathios Filaments:-- Atomic Ruby Red Translucent PETG *affiliate link Phone Tripod Mount by walter is licensed under the Creative Commons - Attribution - Non-Commerciallicense. ...
thingiverse
I was looking for a phone tripod stand and there was nothing usable for a case with a popsocket so I remixed this. (Make sure your popsocket is centered on your phone for it to stay level, it won't work if mounted near the edge.) I used a few...
thingiverse
This is a phone tripod mount designed to be placed onto a tripod either by lever action or by threading the 5.85mm hole on bottom of the device. The device should allow for pictures in both landscape or portrait orientations. The phone mount does not...
cults3d
Universal Phone Tripod Mount. Should work for screen sizes from 4" to 6". It is designed to inprint M6 nut. At the end of layer 23 you have to insert the nut (with 0.3 layer height). Second thing you need is a rubber band. Things you need: M6 Nut...
thingiverse
This is very similar to the [Customizable Phone Tripod Mount](https://www.thingiverse.com/thing:73622) by [samkass](https://www.thingiverse.com/samkass/about) but is not a direct remix. My tripod mounting plate is rectangular, while Sam's model is...
thingiverse
If You Make A Customized Version There have been about a hundred customized versions of this, most of them named "My Customized Phone Tripod Mount". Instead, you can just download your customized part in Customizer without publishing your own...
thingiverse
**[Go to the GitHub page for the full description and the newest files.](https://github.com/DrLex0/print3d-zoom-tripod-notched)** This is a modified version of [LoboCNC's *Zoom Phone Tripod,*](https://www.thingiverse.com/thing:4432319) a small...
cults3d
Can be used with spring or with rubber bands (In the photos it is with springs, but it has some notches to be able to use rubber bands) I was inspired by the design of Dekugelschieber but it is reinforced and modified to use a spring or rubber and...
thingiverse
Universal Phone Tripod Mount. Should work for screen sizes from 4" to 6". It is designed to inprint M6 nut. At the end of layer 23 you have to insert the nut (with 0.3 layer height). Second thing you need is a rubber band. Things you need: M6...
thingiverse
Why buy a phone tripod adapter for <$10 when you could make one yourself for ~$10? I have designed this mount specifically to fit my big phone and then some... my Samsung S20+ fits with plenty of room to spare, so I expect that even the largest...
thingiverse
Cell Phone Tripod Mounting Plate 58.5x59.5x11.2 Print Settings Printer: Home Made Rafts: No Supports: No Resolution: 0.2mm Infill: 25%