phone tripod stand 3d models
199425 3d models found related to phone tripod stand.thingiverse
A no assembly stand I made for my Pixel 3A to use with long exposure astral photography shots Suppports a few different angles to hold the phone at, should work with phones that are just under 10mm thick and 72mm across. ... I printed at 10% infill,...
thingiverse
I design this for my ipad mini 6th, but it can also work for other tablets. ... You will need 1xm3 30 mm screw ( or longer ) 2x m3 nuts
myminifactory
An adjustable tripod mount and stand for phones, inspired by the Glif. It works, but I disclaim responsibility when your phone falls out of it. Buy a Glif. Check out my remix that uses an M5 screw and supports portrait mode. Instructions This uses...
thingiverse
An adjustable tripod mount and stand for phones, inspired by the Glif. It works, but I disclaim responsibility when your phone falls out of it. Buy a Glif. Check out my remix that uses an M5 screw and supports portrait mode. ...
thingiverse
I designed this camera/phone stand to help me film my projects, the design is fairly heavy duty and meant to fit with the threading on my olympus camera while at the same time is collapsible and can become fairly compact. To assemble it you'll need...
thingiverse
The same as the original by Steve5092 but with the letter S removed from the screws. All credit to Steve5092. Print the legs upright with the pivot end down - add support. Ensure the screws have enough wall strength/infill or they snap. ...
thingiverse
I needed a phone stand for my tripod and jsc's one looked best, except it has just 10 mm space for spring. I made end's hollow, so now you have much more space for rubber band or spring in my case. :) ...
thingiverse
i extended the middle and top portion to allow for bigger phones and more room for different sizes of bigger phones. i used 2 3 inch rubber bands tripled over and twisted. i would recommend printing the tip and bottom pieces at a higher infill (30%+)...
thingiverse
This is a remix from https://www.thingiverse.com/thing:4694593 Thanks fo DieZopfe for his original tripod stand design. I liked his design but when I printed it I did come across a couple of issues. First, when I put any weight on the tripod the...
cults3d
Hello, I designed very strong and very practical foldable tripod for phone. This tripod its much stronger and well made than anything else what i saw. Its very easy to print and also very easy to assembly. I didnt want to make plastic screws because...
thingiverse
This project is a mounting system for phones Additional materials for the implementation of this project: screw M6x60, nut M6 Features: fits into standard tripod mount support multiple models of concurrent telephones phone support in a fixed position...
myminifactory
This project is a mounting system for phonesAdditional materials for the implementation of this project: screw M6x60, nut M6Features:fits into standard tripod mountsupport multiple models of concurrent telephonesphone support in a fixed positionnice...
thingiverse
Phone Holder for Tripod Stand .. any size of phone You can glue printed screw to inside part of holder. Beter is to screw it. ... Screw M3 x 17mm Washer Squere Nut 5x5 mm with inner diameter 3mm for the screw
cults3d
PROJECT PRESENTATION This project is a tripod allowing to maintain a phone in all possible positions thanks to a ball joint. The assembly is done without any screws, which however does not affect its robustness. The goal for me is to create other...
thingiverse
###PROJECT PRESENTATION This project is a **tripod** allowing **to maintain a phone** in all possible positions thanks to a **ball joint**. The assembly is done **without any screws**, which however does not affect its robustness. The goal for me...
prusaprinters
PROJECT PRESENTATION This project is atripod allowingto maintain a phone in all possible positions thanks to aball joint. The assembly is donewithout any screws, which however does not affect its robustness. The goal for me is to create other...
myminifactory
You can still do the same with this model and I added some more possibilities : usable on flat surface AND on any tripod/monopod with a standard camera mount, optimized for horizontal and vertical position (horizontal for phones up to ~8.2cm wide, so...
cults3d
You can still do the same with this model and I added some more possibilities : - usable on flat surface AND on any tripod/monopod with a standard camera mount, - optimized for horizontal and vertical position (horizontal for phones up to ~8.2cm...
thingiverse
You can still do the same with this model and I added some more possibilities : - usable on flat surface AND on any tripod/monopod with a standard camera mount, - optimized for horizontal and vertical position (horizontal for phones up to ~8.2cm...
thingiverse
Original leg tends to slip out after a while. ...With this geometry stand will become more sturdy
thingiverse
In case you are just looking for an extended frame, maintaining the V-shaped bracket, there is a remix by ITzAndy94: Extended arm for tripod phone stand [https://www.thingiverse.com/thing:4722194](https://www.thingiverse.com/thing:4722194) This...
thingiverse
TRIPOD_SIDE_3x TRIPOD_CENTER_2x TRIPOD_PAD_3X (roller 8 to 10mm) 1m aluminium round profile 10mm diameter
thingiverse
Phone thickness: 13mm Phone stand size: 55x70xH200mm Display machine: iPhone X
thingiverse
The original phone frame holder was too short for my large phone with case. It is a Note 10. Frame was extended 15mm on the thread side. The channel around where the ball screws in was flattened to remove the need for supports in that area...
cults3d
The original phone frame holder was too short for my large phone with case. It is a Note 10. Frame was extended 15mm on the thread side. The channel around where the ball screws in was flattened to remove the need for supports in that area (Speeds...
thingiverse
Little Stand to put phones on cameras tripods. ...You'll need 2 M3 screws.
thingiverse
This is my stand for phones V2. Check V1 for the other parts. ... You'll need one more M3 screw for the hinge.