phone vent mount 3d models

Remixed from RoBo3D's nice looking mount with some improvements: 1) Vent clip has a barb to attach to vents more securely 2) Opening at bottom for charging cable 3) Vent clip goes deeper for vents with large blades 4) Enlarged arms to fit more snugly...

Remixed from RoBo3D's nice looking mount with some improvements: 1) Vent clip has a barb to attach to vents more securely 2) Opening at bottom for charging cable 3) Vent clip goes deeper for vents with large blades 4) Enlarged arms to fit more snugly...

- Concept of simple, easy and fast to print phone holder with vent mounting mechanism - Printed in PETG took ~1 hour with 0.2mm layer and 0.4 nozzle - Bend two temples after printing and hook them on to vents axle (car has to have this specific vent...

I wanted a phone mount that is held tight so I created a hook with a tension held nut that has notches for the vent fins. To install, turn the fins to down/sideways and hook the back of a fin. Then holding and pulling the ball. ... Turn the nut...

Allows you to mount your phone out of the way of the air vent and other dashboard stuff. I designed this to work with this magnetic mount from Amazon. http://a.co/d/bAuU4Xr or http://a.co/d/8fFpZNR You may have to customize this to fit other types...

This is a phone holder designed to clip to an air vent in a car. This version is specifically fitted for my LG Optimus Q. Instructions Print the holder itself and two legs, then glue the legs to the...

This Universal SmartPhone vent mount for the car is perfect for holding up any smart phone in your vehicle for GPS navigation viewing, displaying a movie for passengers, and more. Makes it easy with sides that slide in and out for larger or smaller...

This Universal SmartPhone vent mount for the car is perfect for holding up any smart phone in your vehicle for GPS navigation viewing, displaying a movie for passengers, and more. Makes it easy with sides that slide in and out for larger or smaller...

without phone) Just put your phone in and take it out, the mount grabs on and lets go via its pivot arms working with gravity. I've tested the mount with phones sized from 2.5"x5" (iPhone 5) to 3.4"x6.4" (Nexus 6 in case) and in between. Prints...

Simple phone mount for Audi TT Mk1 8N. This requires you pulling out your vents carefully using a screwdriver and a cloth, and sandwiching it between the vents and the dash. ... The ball is 17mm.

... closing down on the phone preventing movement. The 'Phone Mount' models have been carried over from the original design without modification. Plans to improve this design after giving this initial version a trial run for a few weeks. ...

This is a remix of the phone holder with a rubber band to hold the arms. ...the arms are also a little bit smaller to slide well out off the printer, no sanding needed.

https://www.thingiverse.com/thing:663700/files

I tweaked Mahow's design (http://www.thingiverse.com/thing:509162 ) to work with an Galaxy S5 body type. In addition, I made the rectangular openings slightly larger to accept the pin connectors without having to manually enlarge them after printing....

I tweaked Mahow's design (http://www.thingiverse.com/thing:509162 ) to work with an M7 body type where the USB connector is offset from center. ... In addition, I made the rectangular openings slightly larger to accept the pin connectors without having...

I have an [iOttie Easy One Touch Wireless 2 Air Vent/CD with 10W Qi Wireless Charging Mount - Black](https://www.target.com/p/iottie-easy-one-touch-wireless-2-air-vent-cd-with-10w-qi-wireless-charging-mount-black/-/A-80228286) that I really like,...

... long as it is not PLA. The coin is designed with a built in support you have to tear apart after printing. Mount the coin like piece to the phone holder using the 4 little screws and then connect the vent piece and use the remaining bolt. ...

I made this for about every car and every phone. ...I hope its usefull

... tight enough to prevent rattling. ... Instructions Print with support, 3-4 perimeters in slic3r. Glue or ABS slurry clips into phone mount. ...Do not wreck your car while attempting to use the phone.

It fits tightly between the louvers and does not allow the phone mount to move around. Very stable. The case is sized for my phone, but I've included the sketchup file so you can modify it for your phone. I printed these in ABS to prevent...

The [Beam Electronics Car Phone Mount Holder](https://www.amazon.com/Beam-Electronics-Smartphone-Car-Mount/dp/B073R68TSH) is great at holding the phone, but not great at attaching to the car. This replaces the clip on the back that attempts to...

designed to slot into the middle air vent on a Rhd 2010 toyota kluger. and fit a phone holder (in my profile) onto it. ...needs no supports, i made mine out of petg to withstand the Australian heat.

Phone holder ball mount that takes the place of one of the Audi A3 airvents

Remixed Magnet holder part adapted to suit MagSafe sized Mounts. ... Specifically designed to fit the MagSafe mount I already had, Linked below https://www.amazon.co.uk/dp/B08T8RFVC7?ref=ppx_pop_mob_ap_share

I wanted a mount for my phone that would sit on top of my in-dash radio/GPS system in my Hyundai Ioniq. ...This slips into the air vents and hooks on to the vent louvers.

This is a phone mount that connects to a car vent. ...Simply print out 2 connectors, put them in the slots and turn, Then connect to the air-conditioning vent in your car.

LG G5 Otterbox defender mount for car vent. You can easily changed the holder size to fit any phone before printing. Use supports for the mount. I used 30% infill for the nut and bolt. ...20% for the mount.

This model is a clamp to hold the phone clamp from Modular Mounting System to car AC vent. There are two sets of phone clamp files. The standard set holds phones up to 12mm thick. The 4mm thicker version accommodates phones with extra thick cases.

This model is a clamp to hold the phone clamp from Modular Mounting System to car AC vent. There are two sets of phone clamp files. The standard set holds phones up to 12mm thick. The 4mm thicker version accommodates phones with extra thick cases.

This is a remix for my car, Hyundai Elantra 2006, which has vertical air vents for the ac. Print and glue the clip using ABS glue (ABS mixed with acetone). ...You need to print two arms.