photon bed 3d models
111667 3d models found related to photon bed.thingiverse
You can use it to hang the hot bed directly on the machine without the need for frequent disassembly.
thingiverse
Meant for using a Creality UW-01 Wash and Cure system with an Anycubic Photon bed.
thingiverse
2mm spacer for an Anycubic Photon Mono, may also fit the Mono 4K. ... This spacer offsets the height added by a magnetic bed allowing you to level the bed without pushing into the screen.
thingiverse
This is attachment designed to stay on the photon mono even during printing. Allows for easy drip of excess resin after printing. Slide the attachment all the way back so it clicks behind the zrod coupler to keep it from moving during print. Image...
thingiverse
I bought a magnetic print bed but it was pretty thick so it was not compatible. As a result, I ended up creating this small wedge which will increase the height of the build plate by 3.5 mm. Feel free to edit the model to change the offset. I just...
thingiverse
2.5mm spacer for optical eye trigger arm for when you fit a magnetic bed. ...Not fancy, not a thing of beauty but does the job.
thingiverse
One of the things I miss about the original photon was how easy you could rotate the bed by 90 degrees after printing to allow hollow parts to drain fully, this design achieves the same thing but at a angle of 88 degrees to keep the top of the build...
cults3d
reuse the original screws) 4 M3 40-50mm (vertical screws, to the bed plate's back) 4 M3 nuts knobs: 4 M3 20-25mm 4 M3 nuts I suggest to Print in petg (70% infil or more). My simil prusa i3 make holes tight (maybe to much): so the holes for vertical...
thingiverse
reuse the original screws) 4 M3 40-50mm (vertical screws, to the bed plate's back) 4 M3 nuts knobs: 4 M3 20-25mm 4 M3 nuts I suggest to Print in petg (70% infil or more). My simil prusa i3 make holes tight (maybe to much): so the holes for...
thingiverse
Same file as this just supported https://www.thingiverse.com/thing:5165751?fbclid=IwAR3XCNAzfvx_vBcpTlKpxLs2pUikLppxLsN18loiqvo-8PGva5V7uMc488Y
thingiverse
Recommended to help save a little resin, and also to save some IPA When the thing finishes printing, Pop the bed off, pop this on. put bed on this, and leave alone for 20 minutes. when you come back, most resin will have dripped off, and your item...
cults3d
apparently people don’t read, make these, don’t post makes or say thanks then whinge the design is crap because they don’t read) This PHOTON MONO bracket allows easy draining of the bed for tall objects. Recommended to help save a little resin, and...
cults3d
Simply finish print, quickly remove print bed, slot this on, put print bed back, leave to drain for a while and come back! shuold help you recover a few ml of resin that would otherwise be washed away! No supports needed, just print with the text...
thingiverse
Simply finish print, quickly remove print bed, slot this on, put print bed back, leave to drain for a while and come back! shuold help you recover a few ml of resin that would otherwise be washed away! No supports needed, just print with the...
thingiverse
This support is permanent and therefore always ready to receive the tray. Very convenient when you already have a busy hand. Printing: PLA, no support, 100% cooling, no special precautions. ... Place it 5cm from the front.
thingiverse
Thanks to the weight of the bed, it does not move while cleaning. Also be aware that the cleaner is no deeper than around 100mm, so you can't clean like this with a full build height. Fits this ultrasonic cleaner: ...
thingiverse
There is no place to put a spacer on the new printer, so you must print an extension when installing a magnetic bed plate for homing purposes. I printed just as it lays in the STL with no supports. Added a thicker version of the one with the...
thingiverse
This support is permanent and therefore always ready to receive the tray. Very convenient when you already have a busy hand. Printing: PLA, no support, 100% cooling, no special precautions. ... Place it 5cm from the front.
thingiverse
https://www.amazon.com/Sovol-3D-Upgraded-Platform-Magnetic/dp/B08LYP2VTT/ref=sr_1_1?keywords=sovol+3d+flex+bed+photon&qid=1638595889&s=industrial&sr=1-1 Unfortunately, it requires a spacer to be placed on the top of the print arm to raise the bed...
grabcad
The rover has a reflective sheet of 20 square meters to deflect the light in the desired direction.Further, it's a compact rover with an onboard processing unit and solar panels on the top acting as ist protecting cover and lid.Additional Payload...
grabcad
Particle Photon microprocessor. ...Arduino compatible IoT wifi embedded platform.
thingiverse
Star Trek's primary means of blowing the crap out of something, the photon torpedo.
grabcad
High fidelity 3D model of the Particle Photon. ...Only other one I've found was in SketchUp and not importable.
grabcad
For all you Sci-Fi fans....a photon torpedo "Similar" to the ones fired by the (star trek) enterprice... ... Likes are appreciated....
thingiverse
A vat scraper for the Anycubic Photon LCD/DLP printer. This is meant for checking that vat for uncured pieces of material. ... **Always be careful when checking the vat as the FEP sheet can get damaged easily**
thingiverse
This is the .STL files of the Photon remote available here https://www.eboardshop.net For best results: Cura settings- Print at 0.2mm or better standing up 100% infill density Support everywhere, overhang angle 84. ... Support density 15% Raft, 18mm...
thingiverse
This is a two piece set to convert your original Anycubic Photon to the neck and baseplate adapter used in the photon mono. The photon mono uses an easy and in my opinion, more stable leveling and fixturing system of four set screws to lock the build...