photon saber 3d models

Hello, I have created a screen cover with hinge for Anycubic Photon Mono 4K, so that at night the light from it does not annoy me when I sleep. The thickness is like this because I used black resin from Anycubic and it came out that in this...

This is designed for a window guide width of 1.1inch see picture and a 3inch exhaust duct.  These parts are designed to be printed on the Anycubic Photon printer.  I suggest printing with ABS resin.  Additionally the parts are designed to be a...

Wanted a bracket to hold the build plate for my Photon Mono at an angle to assist with draining any resin off before cleaning. Looked at a few, and decided to just build one. Build plate is held at 35 degree, and centered over the resin tray. ... V2...

With a good squeeze to the pillar you can attach anything within the enclosure on a photon mono x printer (dont know if it will fit to other anycubic printers). Included are a DIN-rail block for development. ...If you want to change anything the .stp is...

I was inspired by "Photon Zero Dripping Hook Prototype" designed by niccoreyes. I decided to make my own and come up with this four-angle-in-one design. - This hangs the printing platform, both left and right incline in a long side. - This hangs...

... with the resin printer. ... This will print on the Photon S and go together easily if your print is good. ...Make sure you glue the dovetail piece with CA glue or similar so that the back is solid (this part is too long to print as a single piece).

This hook can be screwed into a wall or other supporting structure to hold up the lid on a Photon Mono X. It probably fits other printers as well that have a similar lid. I used 4 drywall screws to screw it into a shelf that sits above my...

It allows you to vary the thickness of the spacer.After I tried to install this on my Photon M3 it turns out that the original file can interfere with the linear bearing unless you are very careful. ...I have made changes to limit that potential on both...

I recently purchased the Photon M3 Plus along with their AirPure filter, only to find that there's no place to put the filter if you have the camera installed. ... This model sits snug on top of the resin pump and provides a platform that fits the...

Riser for the Anycubic Photon M3 lid to allow passage of a small power cord in the back left corner. Useful for things like heaters, air cleaners, etc. Print the single piece if you have a big enough printer. It has also been split into four...

The innovative Antimatter Photon Protected Cam Mount is a pioneering solution that offers unparalleled security features. By harnessing advanced antimatter technology, this revolutionary system creates an impenetrable barrier against even the most...

... the center of the cover to act as a handle for easier removal. The tolerances are tight, but you can place the cover on the vat and remove it without needing to remove the resin vat from the printer itself. This fits the original anycubic photon.

This adapter is custom-designed to seamlessly attach to the vent fan of the Anycubic Photon SLA printer, effectively filtering printer emissions. It accommodates an Enomaker Resin air filter and is designed for support-free printing. ...Minimal sanding...

Made a screw in place holder for the lid of the Anycubic Photon Zero. If you add one of these handles: https://www.thingiverse.com/thing:4619895 (I choose the small one) with this design you can now operate the post printning process with one hand. ... ...

... cut cable tie or even resolder it. It is up to you.For better result you could also seal the printer main lid joint with sealing tape or some other sealing materials. Printer Brand: AnycubicPrinter:  Photon Mono SE Category: 3D Printer Accessories

To further enhance airflow, you can attach an extension air duct to the lower filter opening, possibly incorporating another fan to vent outside the house the filtered air coming from the bottom of the Photon S. The upper filter opening allows for...

The Particle Photon fits perfectly with headers, but there's no outlet for wires. To solve this issue, I added connectors at the top so you can connect solid core wire easily. ... Printer Settings: Printer Brand: Printrbot Printer: Simple Black ...

However, be aware that these designs won't fit neatly on the base of the photon due to increased length. By setting the X-scale to around 70%, you can make it fit within the working area, although it will appear slightly narrower than the tray...

This is a Remix of Skody01's Anycubic Photon M3 build plate drain. I modified it so that the whole build plate is positioned 15mm further to the rear. Now it will not collide with the cover when the build plate is positioned further upward. ...

This lid ONLY WORKS with the Metal photon mono vat. Stock plastic vat will not work.</p><p>-V3 fix overall fit (needs a well-tuned printer so print fits properly)</p><p>-V2 fix corners and other small details</p><p>-Add no logo version</p><p>This...

Since i find very tedious to remove the lid from the Photon I build a counterweight system so It's easy to lift and is out of the way while working on the printer. The pulleys are made from 2 wheels sandwiched together reclaimed from another 3d...

It's compatible with Epax-X1 and Anycubic photon vats, possibly other models as well. I built this using 10mm aluminum pipe for the legs and 8mm pipe for the rotating pins, which I happened to have on hand. The funnel holder is made from M5 screws,...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

Crafted specifically for Anycubic Photon printers, this platform accommodates the resin tanks seamlessly. Once printing is complete, simply slide the tank into place, shielding the lower area from splashes, scratches, and dust. This way, you can...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

... However, this problem can likely be resolved by not fully closing the front lid during ventilation operation. The lower section of this component features four holes for m3 thread cutting, enabling secure internal attachment via the photons lid.

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...