photon validator 3d models

... Easy to print (just check the picture for correct orientation), and if you're using a photon, don't forget to hollow out the parts to save on resin. The funnel with filter I'm using is made from silicone - just expose it to UV light to clean it.

This is a Remix of Skody01's [Anycubic Photon M3 build plate drain](https://www.thingiverse.com/thing:5674605). I modified the inclined holder to also incorporate a slight angle (7.5°) towards the back, so that the resin flows towards only the left...

Couple brackets for the Anycubic Photon Mono X's power supply. Print 2. Install screw through bracket, there's a hole for a screwdriver. Recommend scaling up maybe 2-3% because I made it too tight. ...Screws are #6.</p> <h3>Print Settings</h3>...

I was inspired by "Photon Zero Dripping Hook Prototype" designed by niccoreyes. I decided to make my own and come up with this four-angle-in-one design. - This hangs the printing platform, both left and right incline in a long side. - This hangs...

... the center of the cover to act as a handle for easier removal. The tolerances are tight, but you can place the cover on the vat and remove it without needing to remove the resin vat from the printer itself. This fits the original anycubic photon.

Made a screw in place holder for the lid of the Anycubic Photon Zero. If you add one of these handles: https://www.thingiverse.com/thing:4619895 (I choose the small one) with this design you can now operate the post printning process with one hand. ... ...

A simple resin vat drainer for Anycubic Photon Mono X that can be mounted on the arm. In addition, you can print a base on which put your bottle so the weight will not damage the screen LCD. <b>Update</b> Thanks to @ralvarezg for the <a...

... with the resin printer. ... This will print on the Photon S and go together easily if your print is good. ...Make sure you glue the dovetail piece with CA glue or similar so that the back is solid (this part is too long to print as a single piece).

This is designed for a window guide width of 1.1inch see picture and a 3inch exhaust duct.  These parts are designed to be printed on the Anycubic Photon printer.  I suggest printing with ABS resin.  Additionally the parts are designed to be a...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be 10 of them. The ridges are 0.25mm wide and 0.5mm apart. For each one missing, you are losing 0.25 to 0.50mm of LCD pixels from...

With a good squeeze to the pillar you can attach anything within the enclosure on a photon mono x printer (dont know if it will fit to other anycubic printers). Included are a DIN-rail block for development. ...If you want to change anything the .stp is...

It allows you to vary the thickness of the spacer.After I tried to install this on my Photon M3 it turns out that the original file can interfere with the linear bearing unless you are very careful. ...I have made changes to limit that potential on both...

This adapter is custom-designed to seamlessly attach to the vent fan of the Anycubic Photon SLA printer, effectively filtering printer emissions. It accommodates an Enomaker Resin air filter and is designed for support-free printing. ...Minimal sanding...

I modified a couple of slots on Zerohealth's design to enable printing this bumper on the OG Photon. The added slots make gluing it back in place significantly easier. ... This print needs to be done using Sirayatech Blu or any other resin with high...

This lid also WORKS with Photon Mono -V3 fix overall fit (needs a well-tuned printer so print fits properly) -V2 fix corners and other small details -Add no logo version This resin vat lid keeps dust and other debris out of your resin tank and also...

Hello, I have created a screen cover with hinge for Anycubic Photon Mono 4K, so that at night the light from it does not annoy me when I sleep. The thickness is like this because I used black resin from Anycubic and it came out that in this...

Riser for the Anycubic Photon M3 lid to allow passage of a small power cord in the back left corner. Useful for things like heaters, air cleaners, etc. Print the single piece if you have a big enough printer. It has also been split into four...

I designed a 3-inch exhaust port adapter, allowing me to connect the photon to my existing exhaust fan and safely vent it outdoors. The 3-inch front lip requires additional reinforcement, but that's the only part in need of support. ...If you can't...

I recently purchased the Photon M3 Plus along with their AirPure filter, only to find that there's no place to put the filter if you have the camera installed. ...&nbsp;This model sits snug on top of the resin pump and provides a platform that fits the...

This hook can be screwed into a wall or other supporting structure to hold up the lid on a Photon Mono X. It probably fits other printers as well that have a similar lid. I used 4 drywall screws to screw it into a shelf that sits above my...

Wanted a bracket to hold the build plate for my Photon Mono at an angle to assist with draining any resin off before cleaning. Looked at a few, and decided to just build one. Build plate is held at 35 degree, and centered over the resin tray. ... V2...

The innovative Antimatter Photon Protected Cam Mount is a pioneering solution that offers unparalleled security features. By harnessing advanced antimatter technology, this revolutionary system creates an impenetrable barrier against even the most...

... use with a hose featuring an inline fan. ... This design is tailored for use with the Photon S, and might necessitate some foil tape to ensure proper seating. ... The results are outstanding; this setup almost completely eradicates any lingering odors.

... cut cable tie or even resolder it. It is up to you.For better result you could also seal the printer main lid joint with sealing tape or some other sealing materials. Printer Brand: AnycubicPrinter:  Photon Mono SE Category: 3D Printer Accessories

To further enhance airflow, you can attach an extension air duct to the lower filter opening, possibly incorporating another fan to vent outside the house the filtered air coming from the bottom of the Photon S. The upper filter opening allows for...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be exactly ten of them. The ridges are a precise 0.25mm wide and 0.5mm apart. For each one missing, you're losing a significant...

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

Temperature controller for Anycubic Photon S (probably works with other versions too). Required parts: PTC Heating Element: https://www.amazon.ca/gp/product/B07FJW1DG3/ Temperature Control Module https://www.amazon.ca/gp/product/B08FDTZF3Q/ ...

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

This is a proposal to increase the Z-stroke of the mono X photon printer. The first modification is to the Z-stroke detection system. Simply replace the original part with the part named "Z stroke end detection screw holder" and add a screw that...