pi camera v2 3d models

Snap-on case and mounting solution for the Raspberry Pi Camera V2.

This is a camera mount for the Raspberry Pi Camera V2 that allows horizontal and vertical angle adjustments, but no rotational adjustments. I.E. the camera is always aligned vertically with its mount base. ... It requires 2 - 12mm m2 bolts + nuts to...

A compact case for the Raspberry Pi Camera V2 [link for reference below]. The case is designed to protect the lens from surface scratches. The back cover serves to prevent direct contact with the on-board electronics as well as a mounting point.

This works great for the [Raspberry Pi Camera V2](https://www.raspberrypi.org/products/camera-module-v2/) I found this great mount (see remix original) that required a bit of tweaking, plus I wanted the go pro mount on the top, not the bottom. I...

*** This is an adjustable Pi Camera v2 case I just made to works with octoprint. The front plate can host a Neopixel ring 12x5050 RGB led. There is room for a Pi Camera HDMI Cable Extension available on tindie:...

V2 update this contains the new case for the pi camera v2.1 and a arm model A with a 90 degree turn so you can lower the camera to the build plate! I created this camera holder so that I could tweek the possition of the camera and adjust it any way i...

... kind of mounting geometry. My Assembly Parts List: - Pi Camera V2.1 - Housing Front and Back Parts - M3x8mm Screws (2x for joining the two halves) - M2.5x4mm Screws (4x for securing the camera board https://www.amazon.com/gp/product/B0756TBY2R)

I wanted a pi camera v2 mount that fulfilled the following: 1. has to mount the camera securely (cannot just be a box that has a camera board flopping around in it) 2. has to print without supports (you will have to flip the back part over, but...

... find them useful as well. The mounts hinges are secured using a M3 fastener (I used socket head cap screws and nuts) and the camera is secured using M2 nuts and bolts. For the M2 bolts and nuts I advise using nylon or composite materials. ...

This is just the front part of the camera mount slightly modified to fit the Raspberry Pi camera v2.1.

Camera mount for the Raspberry Pi Camera v2. ...The mount fits the Ultimaker v2 perfectly.

I modified the camera front case from https://www.thingiverse.com/thing:239268 to fit the Raspberry Pi camera V2.

Remixed with round edges and a larger mounting hole to use a M5 screw and a T-nut. ... Fits Pi Camera V2 and V2.1

Remixed with round edges and a larger mounting hole to use a M5 screw and a T-nut. ... Fits Pi Camera V2 and V2.1

IKEA Lack-table enclosure Raspberry Pi Camera V2.1 mount Adjustable at 2 points Required hardware: 1x Bolt M4 x 15 1x Bolt M4 x 20 2x Nut M4 2x wood screw 4 x 20 And of course a Raspberry Pi Camera (V2.1)

There are 5 different height opportunities to hold Raspberry Pi Camera V2 from 30 mm to 95 mm. It is possible to place the camera at 3 different angles. ...(0, 90, 270 degrees)

This is a simple holder for the Raspberry Pi Camera V2.1 The part at the bottom is designed to fit the Anycubic i3 Megs s. ... What you will need to assemble is M3 Bolts and nuts.

A newly designed camera case used for the Raspberry PI Camera Module v2.1. ...The printed parts can be pressed together - no glue needed. Inspired by the [Adjustable/Rotating Mount for Raspberry Pi Camera V2](https://www.thingiverse.com/thing:1718628)

I modified the design for the front of the camera case to fit a Pi camera v2.1, which has a different sensor that is slightly larger. ...See the original design at https://www.thingiverse.com/thing:964961 I have not printed this yet, so I have not...

##**SnapBox Raspberry Pi Camera V2.1 - (Resin)** This **casing** is from our **first** product line **SnapBox** by [**DIYBlender.com**](https://www.diyblender.com/). For more casing examples, visit [**here**](https://www.diyblender.com/). ... For...

Mechanical model of Raspberry Pi Camera v2.1 with PCB, camera module and flex connector to assist in making housings or accessories for the camera. Believed accurate but I wouldn't rely on it without confirming yourself. OpenSCAD source file...

Remixed with round edges and a larger mounting hole to use a M5 screw and a T-nut. Fits Pi Camera V2 and V2.1 Print instructionsCategory: 3D Printer Parts Print Settings Printer: Hypercube Evolution Rafts: No Supports: No Resolution: 2 mm Infill: 30%

SnapBox Raspberry Pi Camera V2.1 - (Resin)This casing is from our first product line SnapBox by DIYBlender.com.For more casing examples, visit here.For more pictures, visit here.

# Frame / Mount for a Pi Camera Module This a frame for Handling a Pi Camera (`v2.1`) , it has a flush mount for the Lens side and a grab handle mount at the back. The idea was to stop my cycle of killing my Pi Cam modules with static - didn't work...

This is a small dongle that lets me adjust the lens screw on the Raspberry Pi camera module v2. It's so small, I didn't even know the lens was adjustable until I read about it online. ...This tool seats into the lens face and allows users to spin it...

A Raspberry Pi Camera V2 adapter for Teaching Tech's Flexible Camera Mount (the generic mount) The front doesn't need supports The back might not need supports. I used them anyways just in case. ... Raspberry Pi V2 Mount for Teaching Tech's Flexible...

A Raspberry Pi Camera V2 adapter for Teaching Tech's Flexible Camera Mount (the generic mount) The front doesn't need supports The back might not need supports. I used them anyways just in case. ... Raspberry Pi V2 Mount for Teaching Tech's Flexible...

Some hardware is required: 1x M4x12 socket head cap screw (https://amzn.to/2PuYJip) 1x M4x25 socket head cap screw (https://amzn.to/2rpkPsQ) 2x M4 nut (https://amzn.to/2Uumk6o) 3x small 2mm outer thread diameter sheet metal or plastic screws,...

The printed parts can be pressed together - no glue needed. Inspired by the Adjustable/Rotating Mount for Raspberry Pi Camera V2 Print instructionsCategory: 3D Printer Parts Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes...

Cam: https://shop.pimoroni.com/products/raspberry-pi-camera-module-v2-1-with-mount Fisheye lens: https://shop.pimoroni.com/products/3-in-1-camera-lens-set Unfortunately I didn't find an appropriate camera case so I tried to design one with SketchUp...