picatinny attachments 3d models

Picatinny rail sight and bottom attachment for the Cobra crossbow found on Amazon The bottom rail also has holes to slot 5 spare bolts through. ... The two stock screws will need to be replaced with M4x20 for the bottom rail, and the top rail needs an...

I made a couple of rail attachments

Picatinny rails are not all the same - some are a tiny bit bigger, some are just a tiny bit smaller. I designed this re-sizable mount that could be printed as one model, but still can move. In order to secure it properly, use M4 screw (about 38 mm in...

This attachment uses 2 1$ Walmart flashlights. The attachment is held on a rail with a 6-32 x 1 1/4 in machine bolt and a matching nut. ... May require sanding of the rail attachment part.

When you need to demonstrate your Nestor-ism at the range, you can use this totally useful and not at all ridiculous attachment to boost your stats at the next Choripaning. ...

Gives you 10cm length of picatinny to attach to, and has a break at the bottom to prevent the picatinny attachment from sliding off the bottom. Overall item dimensions:10.5cm x 3.8cm x 1.3cm No supports needed if you print as oriented in the file....

This is a Molon Labe Picatinny Rail attachment for Airsoft or Paintball guns. ...It may interfere with optics so I would recommend attaching it to the side rails of your airsoft gun.

Picatinny rail attachment for a World War 2 British Sten Gun MkII, MkIII and MkV. Five slotted rail, hinged so it can be placed behind the magazine well. **Use any 1/8in dowel or large cotter pin for the hinge** or print the 'StenRail - Hinge Pin'. ...

Attaches to a standard picatinny rail with M3 screws and a nut. Use supports, and if it has a hard time swinging around try to wiggle it back and forth as a single support line tends to print in the hinge so just pluck that out. ...

Attaches camera to picatinny. Requires 1/4" 16 UNC bolt (Regular camera bolt used in tripods). Airsoft is a sport in which participants eliminate opponents by hitting each other with spherical non-metallic pellets launched via replica firearms...

... battery cover slot. The picatinny rail allows for easy integration between your SplatRBall gun and existing gun attachments. ... Those with 3d printers jump on the opportunity to sell these to your classmates while the guns skyrocket in popularity!

104% scale will fit the best!

I designed this scope for my son's airsoft riffle.  It is designed in 2 pieces, the scope, and the the picatinny attachement.  The picatinny attachment slides right on and is a snug fit on standard picatinny rails.  This is one of my first designs so...

EDIT: UPDATED WITH STEP FILES IF MORE AESTHETICALLY MINDED PEOPLE WANT TO REMIX Made a thumbhole foregrip roughly based on the Nerf Pyragon grip for picatinny rails. Specifically, this was for f10555 Retaliator grips. This model is a tad short...

EDIT: UPDATED WITH STEP FILES IF MORE AESTHETICALLY MINDED PEOPLE WANT TO REMIX Made a thumbhole foregrip roughly based on the Nerf Pyragon grip for picatinny rails. Specifically, this was for f10555 Retaliator grips. This is a longer version of...

Very low picatinny-attached QD slot. NOTE! DOES NOT INCLUDE THE ATTACHMENT POINT. You must epoxy a steel QD slot to the hole. They are very cheap on chinese online stores. ... Get 2-3 different ones and test which one works with your sling before...

A non-functional red dot sight that attaches to picatinny type rails. Remixed from <a href="https://www.thingiverse.com/thing:2587806">Webber1's design</a>. ...I made this for my Nerf blasters and decided to just make it into a single non-functional...

... I took the grip from https://www.thingiverse.com/thing:3111844 And I adapted the picatinny rail from https://www.thingiverse.com/thing:2897402 Use a couple of M3 nuts and screws to tighten down the rails; print with the rails facing upside down.

A sling mount for picatinny 20mm rail. I use it on an airsoft RIF. An M3 screw and nut is needed to fix it in place. ... Yes, it's way stronger than needed, even if printed in PLA.

Picatinny rail attachment for Tactical Torch of 25mm Diameter Designed to be ultra compact and designed for a torch of 25mm diameter Intended for use with Airsoft/Gelsoft toys only Construction requires: - 1 x 35mm M3 screw - 1 x 15mm M3 screw - 2 x...

It's a picatinny to M-LOK adapter, uses screws and nuts to secure onto picatinny rail.no supports needed :)

This is a set of gun attachments from Nanite Systems (Planetside 2) that have been modeled to be compatible with picatinny rails. You will need additional hardware: 12mm M3 screws, and 5.4x2mm M3 nuts. None of these have any added function, though I...

This is a set of gun attachments from Nanite Systems (Planetside 2) that have been modeled to be compatible with picatinny rails. You will need additional hardware: 12mm M3 screws, and 5.4x2mm M3 nuts.None of these have any added function, though I...

If ya'll feel the love for my Remixes/designs feel free to donate to my Paypal - Surfer446@hotmail.com

This is a canted rail that can be used with standard Picatinny rails, this can be used for mounting an optic to the left or right of your main optic. It uses a standard M2.5 bolt to hold it in place however the tolerances are quite tight so friction...

This is a 1x Hcog from Apex legends adjusted so that it can fit on a picatinny rail. ...It is purely cosmetic.

Attach this clip to your molle vests and equipment, and it will allow you to attach any picatinny attachment you may have, from torches, to laser sights and even launchers!

SummaryAttach this clip to your molle vests and equipment, and it will allow you to attach any picatinny attachment you may have, from torches, to laser sights and even launchers!

This part turns your bottom NERF rail into a Picatinny attachment point.

Replaces the stock Kronos front rail with a picatinny rail. ...Now you can easily add any picatinny attachment without the need for an adapter.