picatinny rail for ruger 10 22 3d models
2510472 3d models found related to picatinny rail for ruger 10 22.thingiverse
Picatinny Rail for standard Ruger 10/22, uses all four mounting holes. May fit other models, I don't know. Arc on bottom is a bit too pronounced to sit flat on the receiver, I will update model when I have a chance. Upadated 12/27/17: Reduced...
thingiverse
Standard picatinny rail for the Ruger 10-22, for flashlight/laser/bipod/whateveryouwanttoput on your Ruger 10/22. The rail is designed to be used with standard M4 bolts, and will work best with a M4 washer on the inside of the stock. ... It may also...
thingiverse
Clamp-on barrel mount for the Ruger 10/22 standard barrel. ... Print with 6-8 walls for strength, Print with either end flat on bed to avoid using supports.
thingiverse
Take off the barrel band on your ruger 10/22. hot glue this bad boy on to the front end. attach grip, lights, bipod, laser etc. ...have fun!
thingiverse
Picatinny adapter for ruger 10/22 (tried out with takedown version) Version 4 ist what you can see. Version 5 is what i am working on.. not yet tried out. X.2 means that there are 3 outtakes The holes are to small and you need adjust them a little...
prusaprinters
Picatinny adapter for ruger 10/22 (tried out with takedown version) Version 4 ist what you can see. Version 5 is what i am working on.. not yet tried out.<br/> X.2 means that there are 3 outtakes</p> <p>The holes are to small and you need adjust...
grabcad
When working on my "Left side charging handle for ruger 10/22", I drew the original rail part of the design. Here it is, stand-alone version compatible with the 4 original screws. I prefer this original rail because it is compatible with both 11mm...
thingiverse
When working on my "Left side charging handle for ruger 10/22", I drew the original rail part of the design. Here it is, stand-alone version compatible with the 4 original screws. I prefer this original rail because it is compatible with both 11mm...
thingiverse
... view. ...Mounts perfectly to existing top rail on the fore grip of a Tapco stock for a 10/22 Ruger. Can be used on other weaver rails just ensure stock width is <Model for weaver mount and screws were borrowed from Thingiverse user azaex. ...Enjoy!
thingiverse
Found a great 10/22 stock on Thingiverse but wanted a rail up front for a light and/or laser and also had trouble using the threaded hole at the back for a buffer tube so just stuck a rail back there as well. It's a long model (346mm) so printing it...
prusaprinters
Let me state that this does not contribute to the creation of a weapon, it is a stock which is simply an accessory. Found a great 10/22 stock on Thingiverse but wanted a rail up front for a light and/or laser and also had trouble using the threaded...
myminifactory
My quest into learning Fusion360 continues and I've now produced this Picatinny rail that mounts under the barrel on this specific model (as shown in photos), namely Ruger MkIV 22/45 Lite (2020). There are some different hole configurations than...
grabcad
This is a barrel for a 10/22 I drew. ...This is a work in progress as I haven't found the correct dimensions for the barrel mount.
prusaprinters
this is a rail for the kjworks ruger Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: Doesn't Matter Supports: Yes Category: 3D Printing
grabcad
Work in progress & coming soon! ...Drop-in conversion kit for the Ruger 10/22. ...Based on the legendary Walther WA2000.
thingiverse
This is a fake silencer can for a Ruger 10/22 or Ruger Charger pistol. The Ruger barrel nut will press fit into the hole on the end. (Smaller holes around center are for aesthetics.) Alignment doesn't matter because this slides over the barrel and...
thingiverse
This is my newly designed bullpup stock for the Ruger 10/22. It is much simpler to assemble than most other bullpup stocks I've tried printing. The overall length of the stock is 26.5" no matter what barrel length you use, so either the standard...
thingiverse
I used this to mount my Ruger 10/22 to the wall by my garage door, in case there are some critters out there causing trouble. I had 16" on center studs that I used, which line up well with where I wanted them to hold (behind the trigger and the...
thingiverse
However when adding this grip to some 10/22 designs your hand needs to go up a little higher. So I removed a little material at the top to work with the 10/22. At the same time I added some hex cutouts. ... If you print on its top not much support is...
pinshape
... 100 Notes: Strongest if printed at 100% infill. total parts come out to about 410 grams of filament recommended glue for pla and petg found here https://www.amazon.com/Weld-Acrylic-Adhesive-Applicator-Bottle/dp/B0096TWKCW
thingiverse
... Notes: Strongest if printed at 100% infill. total parts come out to about 410 grams of filament recommended glue for pla and petg found herehttps://www.amazon.com/Weld-Acrylic-Adhesive-Applicator-Bottle/dp/B0096TWKCW
thingiverse
bullpup for 10 22 ruger with standard barrel. I used the receiver mount from the maxis ruger 1022 stock. I downloaded one of these a while back and it had a really great fit so instead of wasting time designing a new mount I used the maxis mount. Any...
thingiverse
Ruger 10/22 wedge taken from the 10-round magazine and to be used on other magazine to improve reliability. Used super glue or glue of your choice to attached. ...Short wedge for magazines with "hump" and longer one for magazines with no "hump" Printed...
thingiverse
Fits the Ruger 10/22 standard barrel. Slips and twist around the front sight. Tested and it works. Printet with 8 walls and 100% infill but can probaly work with less. Requires a short spring with a inner diameter of minimum 9mm and outer...
grabcad
I could not find a complete ruger 10/22 model anywhere so I drafted one up from pictures and measurements from the real steel. Internals are not mil-spec but they work perfectly if 3D printed or milled. All 3D components are modeled entirely by me,...
thingiverse
Some parts were printed 100% infill, like the button for the collapsible stock, the handguard nut and the handguard brace. The factory sight rail on the top of the receiver needs to be removed, and the factory rear sight needs to be removed. Please...