picture frame on stand 3d models

... sized picture frame. ...Made from two pieces the top simply pushes on to the main stand piece and acts as a backstop for the frame to rest against. Just rest your picture frame on the stand for a perfect viewing angle :-) (picture frame not included !)

... we have, so I whipped this up quickly. ...The two "seats" for the picture frame are 18mm wide. Overall it is 200mm wide x 100mm deep x 150mm high. The picture frame on the stand in the pictures is 13in wide x 0.6in deep x 16in high (330x15x406mm).

A stand for pictures or digital picture frames. ...Also suitable for books or other items to stand on.

Stand to replace broken picture frame

Wanted to put a picture frame on my shelf with another in front without blocking the image, so made a stand. ... I use 2 for each frame.

I needed to make a picture stand up on a table. I bought a frame where the uprights and horizontals had a square cross section and made a stand of two feet connected with a wooden dowel. But the dowel is not necessary. ... This is a customizer so you...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=60746 Instructions Using the following options: frame_lip = 8 frame_depth = 7 frame_width = 15 stand = yes stand_tilt = 15 frame_thickness = 15 picture_width = 180 picture_height = 100

This is to replace the broken stand on your favorite picture frames. Easy to scale and attach, requires minimal print time, and few tools. Can be attached with strong adhesive or small screws right into the old hinge. ... Print Settings Printer Brand: ...

For more of my designs check out my website: https://3domcontact.wixsite.com/3dom This is a replacement stand for a picture frame. The one supplied was basically a cardboard part that failed at the hinge (no surprise there). I roughed up the...

I needed to scale down the foldable picture frame stand, the holes were too small once scaled down. My solution is to replace the hinge with a preassembled hinge that comes out of the printer without assembly needed and seems to stay together...

**Summary:** Needed a quick stand for some old wooden wall frames to be placed on tables. Also had some table frames with missing back supports so I threw this design together. I didn't have time to test out options so I am sure that the back...

See the contact detail on our page.For more of my designs check out my website: https://3domengineering.com.auThis is a replacement stand for a picture frame. The one supplied was basically a cardboard part that failed at the hinge (no surprise...

Needed some portable frame stands for an art display. ...Easy to assemble / disassemble to transport.

Easy to assemble stand for a 4”x6” photo frame.Having a few homemade ¾” hardwood photo frames for 4”x6” photos, it was only natural to come up with a sturdy stand for them. Hopefully these will work for you. The stand’s back is around 6” tall and can...

This is a picture frame holder to stand frames which are originally designed to hang on the wall. Can also be used for a tablet. Ich habe hier einen Halter/Ständer für einen Bilderrahmen ohne Standfuß erstellt. Kann auch als für ein Tablet benutzt...

I downloaded and printed [fotofreak58's 4x6 photo frame](https://www.thingiverse.com/thing:5247439) but I wanted it to stand instead of hang The first file is the one I printed but the part needed a little tape around the disk to snug the leg in the...

Just thought the back part needed more support. ... So I made something very similar to the one posted by benny369. The difference between v1 and v2 is the angle at which the picture will stand. ...

A relatively quick print that will save you from having to lean your pictures against the wall or other ornaments. The stand measures 141wx125hx90d The channel is 6.5mm wide. The pocket behind and under the picture is to accommodate the clip.

If you make a picture frame, or some sort of artistic greeting-card-like item, you may need one of these to nicely display your handiwork. So I put this together, and it seems to work nicely. The only challenge is that you need a pin for the...

A relatively quick print that will save you from having to lean your pictures against the wall or other ornaments. The stand measures 141wx125hx90d The channel is 6.5mm wide. The pocket behind and under the picture is to accommodate the clip....

A solution for a broken frame. ... Simple, easy and quick to print. 159mm height 107mm length 10º angle (frame)

This is a two pieces support, combine them and you are done. ... The max supported frame size is: Height 22cm Width 17.5 cm Length 1.8 cm You may have to scale this from 100% to 1000% in your slicer before printing.

This is a two pieces support, combine them and you are done. ... The max supported frame size is: Height 22cm Width 17.5 cm Length 1.8 cm You may have to scale this from 100% to 1000% in your slicer before printing.

A simple rhombus picture frame.

A stand as used on the back of a sports trophy. ...Possibly could be used for some picture frames as well.

 Stand is also voronoi design, and will work with the frame horizontal or vertical and is angled 15 degrees.Interior is slotted by 1mm to hold pictures and the slot is located on the side to slide your picture in.Recommend using a rock style...

This is a customizable picture frame with an optional stand. ... Instructions [Instructions to follow; I haven't printed this thing yet.]

This is a remix of Folding Picture Frame Stand, which uses less material.the original was made by David@3DOMEngineering

My 7 year old asked for a picture frame, so I made a dozen out of some old pallet boards. Then she wanted it to stand up. Shorter one is tall enough, less plastic, so unless I think of any issues with it, I'll run off a bunch of them. My wife...

A generic stand to use for picture frames, objects. I printed mine to hold a college logo. Can be scaled to hold bigger items or smaller items. To be printed "standing up" in normal orientation. ... Please post a make if you like it!