pin support challenge 3d models

I made this " Pin support challenge" but on Tinkercad with Cura, not Full control XYZ. So this is a close clone but not the same. It still does circles for the base. I am curious to see if someone can address this with the same setup. I have tried...

<p>THIS IS A GCODE FILE. This is not an .stl file or .stp file. This is pre-sliced and ready to print. I have only been able to test this g-code file one a few Ender style 3D printers how ever it should work with most 3D printers. If you fell...

<p>Printed on a modded Anet A8.</p><p>For sure I need the volcano hotend.&nbsp;</p><figure class="media"><oembed url="https://www.youtube.com/watch?v=NQaZuawszwg"></oembed></figure><p><a...

Test your printers limits!Pin Support Sphere ChallEnge is a way of testing your printers capabilities. It is designed to be hard to print so only well-calibrated printers with quality filaments will print out a near perfect sphere on a near perfect...

Lapel Pin Challenge #2

IDSA_Lapel Pin Challenge

Lapel Pin Challenge #1

Clip pin for iDSA challenge

my design proposal for the lapel pin

3D printed pin with planetary gears inside the enclosure. ...path like design

3D printable lapel pin for 2014 iDSA Northeast District Design Conference

IDSA 2014 lapel pin challenge

IDSA 2014 lapel pin challenge

My pin for this great challenge !

My first challenge entry; just a simple lapel pin design for IDSA, as the name implies.

I couldn't find a support pin like this one, so my girlfriend drew this for me in Sketchup. ...Not the best finish, but gets the job done.

As an optional plan, I am planning 2 pieces and multi color versions: To prapare two attach parts ( clip and lapel pin adapter ), the 2 pieces plan will adapt to various clothes and situations. I designed the multi color models the premium version...

A circle style pin pad with mag strip reader on the side.

A lovely lapel pin, with USA New york color, is the best way to be presneted in the conferance organized by IDSA, with a smooth surface, and great design shape can offre a good look in all kind of clouths, Designed By Mohamed laouridi hope that you...

The orientation of the bolt head and nut is such that you can remove the bolt once the pin has been pushed into the tube and may help with removal of the pin if you ever needed to. Be aware though that the nut will likely fall out of the trap if you...

IDSA_Lapel Pin Challenge

(see photos to understand...) (For exemple for a 3.3cm total wide safety pin (standard) so 20mm of "not moving part" > scale stl to 89% , no support , no raft > go for 7 minutes of printing !) The printing time is so short , even with high...

simple support bracket with a 6mm pin.

A little support for the pins

Trash Pin Leg press support. ...It was designed with a 6 mm thickness. Trashpins are overpriced now. A good new trash pin will cost starting from 45 dollars. This is a leg pushdown support for the trash pin. ...

Simple shelf replacement pin. Use high infill for stability. ...Print with small support.

This is a pin support for a Keyboard! ...Print Settings Printer: Prusa i3 Steel XL Rafts: Yes Supports: Doesn't Matter Resolution: 0.2

Replacement shelf pin / holder. Use support. Or petter print on the side, so weight of the shelf can't delaminate layers. ...Slightly higher temp helps

I have a large side by side cabinet that needed shelf support pins. The ones I could find on here where too short. The depth of the pin is 7mm and the diameter is 5mm. ... If you print them on the angled back, no supports are needed.

It's a shelf support pin. The diameter is 6.6 mm and the plate is about 15 x 8 mm. ...I print it in 0.02 and infill 100%.