pinky splint cvs 3d models

The customized version of the design can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=45267 with the specified options as follows: Pinky Finger Length - 60mm, CRES - 20, Knuckle Width - 85mm, Middle Finger Length - 80mm, Thumb...

The following options were used in the creation process: Right_or_Left = 0, Thumb Joint Length = 30, Index Finger Length = 73, Middle Finger Length = 77, WT = 2, Knuckle Width = 90, Thumb Metacarpal = 60, Thumb Length = 60, Finger Thickness = 15,...

This customized version of http://www.thingiverse.com/thing:45267 was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=45267 with specific options including Thumb_Bearing = 7, Show_What = Thumb, CRES = 20,...

To create this specific design, the following options were used: Thumb Bearing = 7, Show What = Hand, CRES = 20, Index Finger Length = 90, Pinky Finger Length = 75, Ring Finger Length = 95, Thumb Length = 65, Finger Thickness = 20, Back Hand Length =...

The following specifications were used for this customization: Thumb Bearing - 7; Show What - Fingers; CRES - 20; Index Finger Length - 90; Pinky Finger Length - 75; Ring Finger Length - 95; Thumb Length - 65; Finger Thickness - 20; Back Hand Length...

It includes a foldaway pinky side car to support drinks, while the elbow motion powers its fingers. The thumb is controlled by cables that can be replaced with zip ties if desired. Tendons made of 3D printed flexible filament can also be substituted...

This customized version of the design (http://www.thingiverse.com/thing:45267) was created using the Customizer with options set as follows: WT is 2, Show_What is FullPrint; Pinky Finger Length is 72, Back Hand Length is 70, Knuckle Width is 85,...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Thick = 25 Thumb_Bearing = 7 Index_Finger_Length = 99 Ring_Finger_Length = 98 Knuckle_Thickness = 28 Back_Hand_Length = 94 Thumb_Metacarpal...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: WT = 2 Middle_Finger_Length = 88 Knuckle_Thickness = 28 Thumb_Metacarpal = 55 Fist_Angle = 60 Show_What = Assembly Pinky_Finger_Length = 72...

I modified the grip from Kallunke's excellent model to accommodate my pinky finger within the grip area, rather than underneath it. This design utilizes the same peg system as the original, allowing you to easily replace it with your existing grip.

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Metacarpal = 54 WT = 2 Knuckle_Width = 85 Ring_Finger_Length = 94 Finger_Thickness = 20 Thumb_Thick = 19 Thumb_Length = 64 Fist_Angle = 60...

What you need to print: Hydra Forearm Cuts 1, 2, 3 Hydra Palm Smooth Thumb (1) Smooth Middle Distal (2) Smooth Pointer Distal (1) Smooth Pinky Distal (1) Proximal Finger Connections (4) Hydra Stabilizers (4) Each Actuator, one per finger Hydra Gear...

Instructions: Using the following settings: Back Hand Length: 70mm Middle Finger Length: 95mm Thumb Bearing: 7 degrees WT: 2 Pinky Finger Length: 88mm Knuckle Thickness: 28mm Knuckle Width: 85mm Right or Left: 0 CRES: 20 Thumb Thick: 20mm Thumb...

... ... Dimensions: Height - 500 mm, Width - 360 mm, Length - 360 mm Please note that an ornate antique tea set and delicate pinky finger are not included in this model. This design was created using 3ds Max 2021 software and Corona 5 rendering engine.

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Pinky_Finger_Length = 82 CRES = 20 Thumb_Length = 75 Thumb_Thick = 25 Back_Hand_Length = 94 Finger_Thickness = 20 Fist_Angle = 60 WT = 2...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Ring_or_Finger_Thumb = Right Weighted_Top = 2 Thumb_Metacarpal_Length = 55 Ring_Finger_Length = 95 Thumb_Body_Thickness = 20 Back_of_Hand_Length =...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Ring_Finger_Length = 98 Index_Finger_Length = 99 Finger_Thickness = 20 Thumb_Bearing = 7 Knuckle_Thickness = 28 Right_or_Left = 1...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: CRES = 20 Thumb_Joint_Length = 38 Thumb_Bearing = 7 Back_Hand_Length = 70 Thumb_Metacarpal = 58 Middle_Finger_Length = 85 Knuckle_Thickness = 28...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Fist_Angle = 60 Thumb_Joint_Length = 38 Pinky_Finger_Length = 64 Show_What = Assembly Back_Hand_Length = 70 Middle_Finger_Length = 85...

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Ring_Finger_Length = 98 Back_Hand_Length = 94 Thumb_Metacarpal = 55 Index_Finger_Length = 99 Show_What = Thumb Knuckle_Width = 85 Thumb_Bearing =...

THIS DESIGN WAS MEANT TO ASSIST PEOPLE, NOT HARM THEM, SO KEEP THIS IN MIND BEFORE YOU PRINT - YOU'LL PROBABLY BREAK YOUR PINKY IF YOU TRY TO USE IT AS A WEAPON. CUSTOM DESIGNS AVAILABLE UPON REQUEST AT VERY REASONABLE PRICES! ...INQUIRE IF YOU HAVE A...

We both share a passion for whales and Pinkie is an irresistibly cute model, so I opened Meshmixer to get creative. With precision, I cut a large hole in the top, adding a touch of uniqueness to this DIY project. ... Print Settings: Printer Brand:...

... 2-Finger Grip - Concentrate on index and middle finger power. 1-Finger Grip - Train your pinky finger for ultimate dexterity. The grip's sides are a sturdy 140mm, providing stability during intense training sessions. ...Stay Safe, Train Smart.

http://www.thingiverse.com/apps/customizer/run?thing_id=45267 Instructions Using the following options: Thumb_Thick = 25 Thumb_Bearing = 7 Index_Finger_Length = 99 Ring_Finger_Length = 98 Knuckle_Thickness = 28 Back_Hand_Length = 94 Thumb_Metacarpal...

-5% pinkie and -3-2% for the ring & index ones. ...On the slicer 1) scale STL for the desired size 2) select number of the walls (3-4) a bit over extruding & heat will make part stronger & zero infill 3) Zero ('0') bottom layers Category: Outdoor &...

I crafted this accessory for my Kel Tec P11 because its original design left my pinky finger hovering uncomfortably below the magazine, a problem that this solution promptly resolved. I printed it in a subtle grey hue to ensure maximum visibility in...

I'm a fan of its miniature size and quirky design, reminiscent of Pinky from the Doom movie. Its lack of detail is part of its charm. This creation has been optimized to extreme levels, making it one of the most refined examples of min-maxing I've...

These pinky extensions for Taurus G2C magazines, 9mm and 40 S&W, have yielded optimal results when printed with PETG filament. However, I've encountered significant issues with the 9mm base model, which consistently displays imperfections. Despite...

... with appropriately longer screws and knobs. The MiniAdder V2 Pinky Protector fits this model. The overall length is around 128mm and the diameter is 35mm. ... Bolts and nuts that are needed: 2x M4x30 screw 2x M3x30 screw 2x M4 nut 2x M3 nut

These miniatures are from the Monstrober 2021 October Collection.Pre-supported version for all the miniatures is included!This collection includes the following 31 miniatures:Closet Mimic, Ghost, Flying Swords, Fire Beetle, Gibberling, Leucrotta, Mud...