pint x float plate 3d models
509136 3d models found related to pint x float plate.thingiverse
This is a protective float plate for the Onewheel Pint X. The design features flared sides in addition to a full plate covering the underside, protecting your gear while maximizing ground clearance. The float plates are mounted on the board using 3M...
thingiverse
Rear skid plate for Onwheel Pint X Attach with heavy duty Velcro https://www.amazon.com/GOHOOK-Inch-Adhesive-Black-Hook/dp/B088YMMKD4/ref=sr_1_8?crid=1JM9M63HDVP6B&keywords=heavy+duty+velcro&qid=1646870333&sprefix=heavy+duty+ve%2Caps%2C204&sr=8-8
thingiverse
Pint X rear skid plate with bolstered strike zone attach with heavy duty Velcro
thingiverse
Removed logo text on the full length onewheel pint x rear skid plate that covers the rails as well made by WarPig.
thingiverse
Modification of SkyhawkPilot's Pint stand to better fit the Pint X
thingiverse
... adhesives. I printed on HutchBox ABS without support on X and support added on PINT (for the catch lips). ... Brim or skirt might be needed on your print as I have observed the corners (especially PINT) start to curl up midway through the print.
thingiverse
Protective cover designed for the Onewheel Pint X's charging port (may fit other Onewheel models, but I've only tried it on my board). It should fit snugly, with the open side of the cylinder facing the top of the board. Designed to fit a keyring...
thingiverse
This is a footpad that goes directly onto the rear footpad made to be compatible with the CNR Pint/Pint X Extended Footpad Have yet to have any issues during testing. MATERIAL: TPU INFILL: 100% Use VHB tape to mount to board use whatever...
thingiverse
Warning - this works for Pint X bumper with TFL float plate installed (I glued it with Mamut Glue). Also, I'm not sure the printer was properly calibrated, you'd need to double check the dimentions. Walls thick enough so at least the part that...
thingiverse
something I have been dreaming up. the idea is to offer more control and stability while planting the rear of the board in the dirt while going down steep inclines. ... attach with heavy duty Velcro
thingiverse
Protects edge of OneWheel. Attaches by press fit into screw holes. ...The thin version is an improved version in which an M5 screw can be used to increase the holding pressure in the hole.
thingiverse
Onewheelk Pint / Pint X charger port cover. The is designed with a rail guard in mind. Depending on the accuracy of your printer, you may have to either dan down thestib a bit or increase the size by a percent. ... Print with logo facing up and...
prusaprinters
A plug similar to the original one from Onewheel, but less prominent and printable without supports, and a fancy looking, flush, magnetic plug.You can find the MAGNETIC Charger Plug files here.You need some flexible filament to print the FLEX Charger...
prusaprinters
A plug similar to the original one from Onewheel, but less prominent and printable without supports, and a fancy looking, flush, magnetic plug.You can find the FLEX Charger Plug files here.You need two magnets (5x5mm *) for the Magnetic Charger Plug....
thingiverse
Nose handle for the Pint X. There is plenty of space in the front bumper, I think it should have come like this :) Using the grid pattern on the inside as a guide, Dremmel out a 6x2 section. Then glue the nose handle in place. I printed in 95A...
thingiverse
based off "thewilldconstructs" this is suited to the vesc ubox 80/100 fits but is snug for the pint x also included is a box for Bluetooth and phase wire holder to hopefully negate vibration and fatigue best to apoxy phase wire holder to the base...
thingiverse
Fox Float X Volume Spacer 0.6" CC 0.8" CC Tested on Fox Float X 2017 216x63mm
myminifactory
Still A WIP so any suggestions or fixes are strongly encouraged :) This model is primarilly desinged for expanding a Pint's battery capacity to that of a PintX or more (if you're capable of pulling that off). Using a Onewheel Pint and some stock...
thingiverse
Upgrades a Fox Float X "Performance" to a standard version. Just remove the black plastic cap and press this printed cap on, make sure the egg-shaped indentation on the inside is oriented the correct way. Adds Low-Speed Compression tuning to your...
thingiverse
In the Handlebar clamp: hall sensor, led On the shock: servo The parts are compatible with: Fox float x shock 2017 Fox 36 fit4 fork (tapered) 2017 Bikeyoke triggy dropper seatpost lever Other parts: Arduino pro mini 18650 battery hall sensor magnet...
thingiverse
Full details on my blog https://edditiveblog.wordpress.com/2016/11/10/3d-printed-action-camera-floaty/ Print Settings Printer: Cocoon Create Rafts: No Supports: Yes Resolution: 0.2mm Infill: 100 Notes: I printed using a brim to minimise warping off...
prusaprinters
Full details on my blog https://edditiveblog.wordpress.com/2016/11/10/3d-printed-action-camera-floaty/ Print instructionsCategory: Camera Summary Print Settings Printer: Cocoon Create Rafts: No Supports: Yes Resolution: 0.2mm Infill: 100 Notes: I...
cults3d
... you to easily attach any brand of floaty (eg. ...GoPro) to the Garmin Virb X or XE camera. Simple snap design that securely holds onto the camera. ...Full details on my blog https://edditiveblog.wordpress.com/2016/11/10/3d-printed-action-camera-floaty/
myminifactory
... you to easily attach any brand of floaty (eg. ...GoPro) to the Garmin Virb X or XE camera. Simple snap design that securely holds onto the camera. ...Full details on my blog https://edditiveblog.wordpress.com/2016/11/10/3d-printed-action-camera-floaty/
thingiverse
Volume spacers for Fox Float X 2022 for 3D printing 0.2 to 1 cubic inch per 0.1 increments Do not look like the original parts but still fit just fine. ...Install with number facing you.
thingiverse
1st upload, let me know if there are any problems ( updated below) I've added a prevision to the 2 x 3 endcap by GMoi for a float to run a wick system. GMoi end cap https://www.thingiverse.com/thing:1687195 Hole is for 1/2 NPT, 0.870" ID I...