pipe to garden hose adapter 3d models
2189836 3d models found related to pipe to garden hose adapter.thingiverse
I am using this in my RV to adapt the exterior shower hose to a garden hose so that I can hook up an outdoor Fillet Table that has a sink and faucet. ...Cost: $0.48 Print Settings Printer Brand: RepRap ...
thingiverse
i modified the garden hose to screw it with a 1" filet
thingiverse
This is a coupling that adapts from female garden hose to female 3/4" tapered pipe thread. It was needed on my water pump (male garden hose thread) to hook up to a 3/4" PVC water line. The garden hose side uses a rubber washer (like all garden hose...
thingiverse
Remixed this from this design and also this design and also a Female pipe thread design to connect a garden hose onto a water pump that I have that is Male NPT Female Pipe Thread Design I Remixed With: https://www.thingiverse.com/thing:4908168...
thingiverse
garden hose to 40mm drain pipe. ... garden hose connection to rinse a 40 mm drain pipe. ... fits almost all quick connect garden hoses.
thingiverse
This is a garden hose to pinlock adapter for use in home brewing or whatever you would like to do with it. ...:)
thingiverse
Adapter to switch from 20mm garden hose to filter pump hose. 32mm. Useful for small pools that do not have an outlet for a filter pump but for drainage. You can use this outlet to connect the filter pump. I have printed this piece with PLA, but it...
thingiverse
This was a combination of two items from Thingiverse: https://www.thingiverse.com/thing:551238 and https://www.thingiverse.com/thing:10189 The garden hose threads fit nicely on a real hose, and they can be printed without support at 0.2mm layer...
thingiverse
Made an adapter for my dehumidifier to go into the condensate pump.
thingiverse
... ... This is an adpater that will allow you use to connect a water hose to the faucet. It can be customized for whatever project needed. For the time being it, is a work in progress. It is a pretty heavy customization of the nuts and bolts openscad.
thingiverse
Remixed this to be a bit longer from https://www.thingiverse.com/thing:219625
thingiverse
Used to this piece to hookup garden hose attachment from de-humidifer to abs pipe. Printed in ABS of course. ... Note: Print at a 90 degree angle and use garden hose washer to secure hose
thingiverse
I made this Guillemin coupling to Gardena garden hose coupling adapter at work. This allows me to connect a garden hose with quick lock connector to a fire hydrant with what is apparently called a Guillemin connector. This is a two part design which...
cults3d
An adapter for 32mm INTEX pool hose to 18mm garden hose
thingiverse
rv antifreeze adapter to garden hose, adapts 1 gallon rv antifreeze jug to garden hose (3/4-11.5 GHT thread)
thingiverse
Pop, soda or water bottle to male garden hose adapter. To connect a water bottle to a garden hose or other plumbing. ...Use a garden hose washer to seal the water bottle connection.
thingiverse
Quick and dirty NPT to quick release garden hose adapter. ... Print with 4-5 perimeter layers, 50%-70% infill.
thingiverse
Output adapter for water heater to garden hose. For bench testing a water heater away from the normal hookups. 3/4 NPT/ FIP to garden hose male Print at 100% infill to avoid leaking between layers. May need center drilled out, teflon tape to...
thingiverse
This adapter will allow you to connect a garden hose to a military surplus water can. ... I use it to add water to the fresh water tank of my travel trailer while boondocking.
youmagine
... store and the "work around" was more than $10. I got the threads for the PVC from mcmaster and the garden hose threads form the link to thingiverse. To clarify, this is a female 3/4" GHT (Garden Hose Thread) to male 3/4" NPT (National Pipe Thread).
thingiverse
Allows for the attachment of a 1.25 pool hose to garden hose print the o-ring using TPU
thingiverse
I don't have a sump, so I made this adapter so I can run my pump and utilize pressure inside my filter to drain through my garden hose and into the front yard. My garden hoses leak a lot, but this setup is draining my spa very quickly. ... Print...
thingiverse
Adaptor for the shower head to a garden hose, npt type.
thingiverse
My sink faucet has 7/8-24 UNS thread type so I created an adapter to hook into a garden hose for Aquarium water changes. Internal bore is a cone for better flow and a stronger print. Print time was about 90mins. Hose threads fit extremely well,...
thingiverse
This is an adapter that goes between my Moen gooseneck faucet and a garden hose, so I can connect my sink to my fish tank syphon / refill adapter. The Moen faucet is some weird custom thread setup so I ended up having to put calipers on it to get...
thingiverse
I looked on Thingiverse and elsewhere to find a 3/4" to Garden hose adapter and did not find one. I found STEP files for a 3/4" NPT coupling and male garden hose fitting and generated a printable transition between them to make this design. This...
youmagine
Here is an adapter that screws onto standard 56/64-27 thread faucets (after removing the aerator) and allows a standard 1-1/6-11.5 garden hose to be attached to the other end. An additional o-ring or two may be required to prevent leaks. I would also...