pir sensor case 3d models
233297 3d models found related to pir sensor case.thingiverse
# HC-SR501 PIR Sensor Case # Summary This thing is a simple bolt-on case for the HC-SR501 PIR Sensor, the case is designed so that it can slide onto my Panasonic TV and face the rest of my room. The case was designed using an open source step file...
thingiverse
This is a case for the PIR motion sensor HC-SR501. It comes in to parts that perfectly enclose the sensor, with a small opening for the wires on the back. ...Designed with Tinkercad.
thingiverse
When the PIR sensor detects a motion, the ESP32CAM wakes up, takes a couple of photos and saves them to the microSD card. After that, if wifi is accessible, it will try and transfer the pics to a locally set up FTP server. If the transfer was...
thingiverse
These are the motion sensor enclosures I used in my YouTube video
thingiverse
I ordered some PIR motion sensors off of the internet (see link below and last photo) to trigger lights in my house. They work very well but I needed a smaller case for one so I designed this case. The circuit board in these units can be removed...
thingiverse
Created my own Passive infrared Sensor cases. This is modeled around a Radioshack PIR. I added 9 leds for effect. I am still working on the Base plate with battery compartment and will add the posts inside for the screw in terminals. I added the base...
thingiverse
Designed this case to hold a HC SR501 motion sensor that I use for my Halloween props. ... It's pretty basic, but it gets the job done.
thingiverse
... you can modify. I have cnc'd this one and adapted few of the measurements. Now, updated to increase internal height, so there is enough space for those electrolytic caps. Instructions These sensors (SR501) could be found under $2 in ebay.
cults3d
This case is for the pir sensor module. the sensor must be fixed inside the box either with hot glue or with the two screws through the respective holes. the model allows you to adjust the sensor once it is fixed to the wall. ...Only one M3 screw and...
thingiverse
Therefore I buyed the standard sensor for indoor use and build a case to mount it outdoors in a 30° angle within the carport. ... I strongly recommend to seal the sensor around the lens with some glue and to cover all holes on the back with tape to...
thingiverse
Here three solution to mount the PIR sensor model MR-HW06A or MR-HW06A: -in 503 plaque adapter wall mount -up-down box -in rotating box + - 25° angle (thanx to @DieZopfe remixet ball joynt) choose your favorite solution and print it with no...
thingiverse
Yet another motion sensor case I made. I like the simplicity of the design. [EDIT1] I just added a little more sturdy lid. ... [EDIT2] New front case with female micro USB connector hole.
thingiverse
There is also openings on the case for adjusting the time and sensor on the PIR. I also used 4mm screws for the swivels but gave the base of the case a extra screw point should you want to use self tapping screw to mount the case to the mounting...
thingiverse
Yet another HC-SR501 sensor case :) Designed my, so that i could connect the mounted sensor with a 3 pin 3.5mm jack connector. You need to connect the sensor with jack socket with 3 cables through the rectangular holes. The cover is a snap-fit...
thingiverse
This is a custom case for PIR motion sensor. ...I design it to fit inside an Arduino pro micro or an Arduino nano with a 433Mhz attached!
thingiverse
Simple case for a motion sensor and an esp8266 should interlock all togheter without need of wires
thingiverse
Printed in ABS without support. ... use self tapping screws 2pcs M2x8 for sensor 4pcs M2x10 for back plate
myminifactory
Yet another HC-SR501 sensor case :) Designed my, so that i could connect the mounted sensor with a 3 pin 3.5mm jack connector.You need to connect the sensor with jack socket with 3 cables through the rectangular holes. The cover is a snap-fit that...
thingiverse
PIR module is PIR HC-SR501. ... Micropython code for the ESP32 at https://github.com/divergentti/kotiautomaatio/tree/master/esp32/liiketunnistin Another design for ESP32-Wroom-32 without external antenna is available too, but perhaps this version...
thingiverse
PIR module is PIR HC-SR501. ... Micropython code for the ESP32 at https://github.com/divergentti/kotiautomaatio/tree/master/esp32/liiketunnistin Another design for ESP32-Wroom-32 without external antenna is available too, but perhaps this version...
thingiverse
The original version was too short to fit the pins and stuff. I played around a bit and this one seems to fit nicely. If you look at the whole picture, it shows the original on the right, and a version that is too long on the left. ...What you are...
thingiverse
Designed the smallest possible case for the HC-SR501 PIR with snaps, mounting posts and indexing notch. Can be mounted with screws or double-sided tape. ...Snaps are strong and reusable.
thingiverse
Customized version of https://www.thingiverse.com/thing:266912 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=266912
thingiverse
This is case for hc-sr501 motion sensor and different MQ gas sensors in one box.
thingiverse
ESP-32S ESP-WROOM-32 PIR Dual relay DHT11 sensor case