pivot weapons pack 3d models

Discover how to use tape rolls effectively on your plotter by watching this video: https://www.youtube.com/watch?v=z6GaBOqir8Q In the video, you'll learn techniques for better handling and application of tape rolls on your plotter, ensuring smooth...

Initiating a new phase...

Material is Cobalt.Density = 0.01 grams per cubic millimeterMass = 48008.37 gramsVolume = 5394199.26 cubic millimetersSurface area = 242568.33 square millimetersHP1:I sketched out the front of the part by starting with a 45 diameter circle in the...

I started out with 2-D sketch then extruded figure. Then i sketched the top place and cut a hole in the middle of figure. ...then I continued to the right plane and extruded cut the side of the figure.

Mass = 48008.06 grams1. Make a sketch on a pane with a 45D circle on the origin. make a vertical like 50mm tall 120mm away from the circle from that line make a horizontal line 300m toward the circle from that line make a line going slightly up...

Material: CobaltTools: Extruded base, Extruded cut, shape tools, filletMass:14497.06 grams (I know it is not the same as the example)

Mass = 18252.46 gramsVolume = 2050838.72 cubic millimetersSurface area = 210429.73 square millimeters

something to use

I created this by making the original shape then adding the additional features, specifically by making a reverse offset for the last part.

Test prep project

Mass = 13022.90 gramsVolume = 1463247.41 cubic millimetersSurface area = 226232.83 square millimetersJust like the other models, I started by creating a sketch on the front plane. I then extruded the sketch I drew using the Extruded Boss/Base tool.

Mass = 18252.46 gramsVolume = 2050838.72 cubic millimetersSurface area = 210429.73 square millimetersProcedure: I started this model with the sketch from the front view, making sure to set the angles and radiuses to the correct dimensions. Then, I...

First, I started by sketching the front plane with 300mm line on the bottom and on the left side, a horizontal line 50mm up. Then made a centerline 120mm from the left bottom point in order to make the centerline for the circle. Then, I went over to...

For the first model, I created the sketch with the circle hole in the middle. I then created all of the vertical and horizontal lines, leaving the tangent curves for last. For the second model, I did a cut extrude through the mid plane, and cut off...

The first step in creating this model was quite easy, just a simple sketch extrude of the oval-ish side profile. And to create the large gap in the middle, I sketched it out on the top plane and extrude cut the model. As well as a 45 degree chamfer...

1. made 1st config with sketch extrusion2. supressed features on second config3. cut model in half4. top view sketch and cuts5. mirror6. hole through center cut7. another config with suppression8. made new sketch on side view 9. cut out a bit10.

CSWA Exam

3D

Made in solidworks 2021

I made this model by building a sketch and adding dimensions then after building the feature I updated the component so it matches the other configurations

The first step in creating this model was quite easy, just a simple sketch extrude of the oval-ish side profile. And to create the large gap in the middle, I sketched it out on the top plane and extrude cut the model. As well as a 45 degree chamfer...

The user requested that I behave like a Text Rewriting Bot and provide rewritten versions of inputted texts while maintaining the original tone, voice, and phrasing. ...The rewritten text should have an Flesch-Kincaid score of 100%, use active voice,...

Step 1: draw a 2d sketch rough outline on the front plane with proper dimension and boss extrude but make sure you put extrude on midplaneStep 2: now go too the top plane and you'll make some cuts, first you'll make some triangle on the side that's...

I created this by making the original shape then adding the additional features, specifically by making a reverse offset for the last part.

3D

something to use

First, I started put by sketching the side profile and boss extruding it, leaving the circle hole in the middle. Then, I added two triangular cut extrudes at the top of the model, and two rectangular cut extrudes attached to each other in the...

school education