plant pot dishes 3d models
68535 3d models found related to plant pot dishes.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714535 Instructions Using the following options: show_Part = all waterBase_height = 7 outlet_Diameter = 5 dish_height = 15 waterRes_diameter = 60 waterRes_bottemGap = 6 dish_support_length = 10...
prusaprinters
Just in case your filled with excitement with the Plant Pot and start filling it with dirt and water, only to find out it leaks (because there were not enough bottom layers or it wasn't sealed with clear gloss), here is a quick disk to set it in.
cults3d
Customized version of http://www.thingiverse.com/thing:714535 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=714535
thingiverse
Dish designed to hold a Moss Ball or other plant pots. The raised edges and dip in the middle are to keep the water from spilling over the edges. I would recommend coating it in some kind of waterproofing to prevent damage over time if PLA is...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714535 Instructions Using the following options: waterRes_height = 90 pot_curve = 100 pot_height = 90 waterBase_height = 7 dish_support_length = 10 dish_support_distant = 30 outlet_Diameter = 10...
thingiverse
Simple 112mm internal diameter with an external diameter of 120mm. ...Lip from floor to internal diameter is 5mm, from internal diameter to external diameter is 20mm. Makes for a nice planter dish.
thingiverse
If what you're planting requires drainage, this planter will provide: the design includes a built-in dish that collects the water from four holes in the base of the pot.
thingiverse
A stylish cuplike vessel for the containment and nourishment of a photosynthetic organism. ...Printable on a 10x10x10cm printer, Includes drain holes from the cup to the dish. ... Designed in Blender.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714535 Instructions Using the following options: waterRes_height = 57 thickness = 2.5 pot_curve = 100 dish_support_height = 3 dish_support_width = 25 waterSupport_amount = 25 dish_support_amount...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714535 Instructions Using the following options: triPot_distance = 30 waterRes_height = 57 dish_support_height = 3 dish_support_distant = 30 thickness = 2.5 funnel_diameter = 20 show_Part =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714535 Instructions Using the following options: outlet_Diameter = 5 funnel_height = 10 dish_support_amount = 6 resolution = 40 triPot_distance = 30 pot_diameter = 80 dish_support_distant = 30...
myminifactory
Waterproof 3D printing tips & tricks:https://3dwithus.com/3d-printed-plant-pots-self-watering-planters-waterproof-3d-printing PETG Filament Pros & Cons:https://3dwithus.com/petg-filament-review-waterproof-pros-cons Glueless bed adhesion optimized...
pinshape
Waterproof 3D printing tips & tricks: https://3dwithus.com/3d-printed-plant-pots-self-watering-planters-waterproof-3d-printing PETG Filament Pros & Cons: https://3dwithus.com/petg-filament-review-waterproof-pros-cons Glueless bed adhesion...
thingiverse
Small water dish for a pot. Has a 60 mm bottom diameter to accommodate a pot. The lip goes up at a 60 degree angle to catch any excess water. About 11mm total height of the tray. Top edges are radiused slightly. ... Printed on MakerBot Method X with...
pinshape
Customized version of http://www.thingiverse.com/thing:270289 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=270289
thingiverse
Customized version of http://www.thingiverse.com/thing:270289 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=270289 Instructions Using the following options: ...
thingiverse
Customized version of https://www.thingiverse.com/thing:714535 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714535
thingiverse
Customized version of http://www.thingiverse.com/thing:714535 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=714535 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:714535 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714535
thingiverse
Waterproof 3D printing tips & tricks: https://3dwithus.com/3d-printed-plant-pots-self-watering-planters-waterproof-3d-printing PETG Filament Pros & Cons: https://3dwithus.com/petg-filament-review-waterproof-pros-cons Glueless bed adhesion optimized...
cgtrader
Title: Terracotta Plant Pot Description Photo-realistic Terracotta Plant Pot and dish with cloned photo textures produced in photoshop. There is a joined pot & dish version on layer one, and separated into two objects and parented on layer there. ...