plastic pyrex lids 3d models

While not too expensive, I was annoyed enough create these replacement lids that I could print anytime I needed. At first, I tried printing in PETG because it is a bit more flexible than PLA. Unfortunately, it is not flexible enough and these lids...

I have small plastic containers that hold dog food. These containers have lids and they don't stack very well. So I created this holder to solve my problem. The size should also work for mason jar lids.... ... Here is the link to Tikercad ...

Simple lid holder for the Pyrex glass container set.

Pyrex refractory lids TPU material prints in 6-7 hours and fits you perfectly! ... STORAGE COVER

This is a replacement vent lid for Pyrex containers like this one: https://www.pyrexware.com/pro-3-qt-round-vented-plastic-lid-turquoise/1121732.html#start=33 This is just for the vent cover in the center of the lid. DISCLAIMER: Depending on what...

This is a replacement vent lid for Pyrex containers like this one: https://www.pyrexware.com/pro-3-qt-round-vented-plastic-lid-turquoise/1121732.html#start=33 This is just for the vent cover in the center of the lid. DISCLAIMER: Depending on what...

I was tired of the large number of Pyrex lids falling all over the place. The lid holders out there hold them sideways, which doesn't allow stacking and are space inefficient. So I designed these 3 prints for Pyrex lid holders. One for 1 cup, 2 cup,...

This is a Pyrex lid holder that I designed. It holds the largest round lids down to the smallest ones. It was designed for the amount of lids we have but I'm sure it could be adjusted to fit anyone's needs. ... This thing took around 18 hours to...

... wear out pretty quickly and don't "snap" anymore at all. I designed these in Fusion 360 to fit over the top of the regular lid and retain the snap tabs in place. They stay in place nicely and seal the container the way it was intended to be. ...

Pyrex lid Storage solution. I was tired of all the lids just being thrown in the cabinet, so I designed and printed this solution. I designed it with the round bottom shape instead of boxed off in an attempt to save plastic, but then realized it...

... So, after getting tired of the lids jumping out of the cabinet (I'm sure all of you have seen the commercial https://www.youtube.com/watch?v=FhZcyiCUzng) I decided it was time to print something that could hold the lids without them rolling around.

As you can see in the pics, the larger version works for several of the larger sized lids and the smaller was specifically designed for the small round lids. There are also dividers to help separate different sizes/styles of lids. This was...

... my name, embossed, you can remove that or put your own in to brand your lunches. Github: (https://github.com/donbowman/pyrex-lid-stopper) Blog: (https://blog.donbowman.ca/2018/04/01/the-case-of-the-missing-pyrex-stopper-3d-printing-to-the-rescue/)

We keep losing the vent lid plugs on our Pyrex food containers down the drain, and you can't buy them separately. I made a mold to make replacements from oogoo. ...GE Silicone I is apparently safe for "incidental food contact".

This fits Pyrex containers with the red rectangular lid. I used TPU. ...Might try Nylon

Lid holder/organizer for round 2 cup Pyrex lids. They hold 6 lids each. ...Two versions, one is slightly thinner to take up less space.

The lid is 126mm in diameter and 10mm high and fits over the Pyrex bowl, just like the original lid. The original Pyrex lid is quite robust and can withstand high temperatures and safely go through a dish washer. I can't say the same for TPU, so...

The lid is 126mm in diameter and 10mm high and fits over the Pyrex bowl, just like the original lid.The original Pyrex lid is quite robust and can withstand high temperatures and safely go through a dish washer. I can't say the same for TPU, so care...

The lid is 126mm in diameter and 10mm high and fits over the Pyrex bowl, just like the original lid. The original Pyrex lid is quite robust and can withstand high temperatures and safely go through a dish washer. I can't say the same for TPU, so care...

Replacement tab for your pyrex lid after you lose the original while washing dishes unprompted and your better half yells at you. Instructions Print with the flat side down. Snaps in place tight.

Had a co-worker bring in a pyrex bowl with a broken lid. This lid works really well! Print Settings Printer Brand: Robo 3D Printer: ...

... with PLA. It weighted about 80grs after printing (not cheap to print). I added a small watermark inside the lid, but it should print just fine. I do have the design without the watermark for anyone who is kind enough to tip. Happy printing. ...

This is a top/stopper/lid for a Pyrex salt and pepper shaker. I see them around, and sometimes, they don't have a top, so I busted out the 3D modeling software. Print Settings Rafts: Doesn't Matter Supports: Yes Infill: 100% Notes: The file name...

Pyrex Centrifugal Pump 3D Model V-ray render engine- BY Said Ibrahim

A stand to convert a 60 degree 100mm Pyrex funnel (~$17) into a pour over. ... The Funnel: https://www.amazon.com/gp/product/B010RHDQ0G/ Enjoy your Coffee.

Photo-realistic Pyrex Mixing Bowl _Pyrex (trademarked as PYREX) is a brand introduced by Corning Inc. in 1915 for a line of clear, low-thermal-expansion borosilicate glass used for laboratory glassware and kitchenware. It was later expanded to...

Lid for Pyrex 8x6 1.5L / 6 cup rectangular baking dish.

This was designed to help declutter a cabinet that held a lot of Pyrex glass bowls that nest inside each other. Now I can stack 4 full sets in a much smaller area, freeing up most of the cupboard space. The expansion bottom piece was created so...

I melted the lid for my 6" round Pyrex food container in the dishwasher. ... Created this replacement with Flexible TPU filament - Fits really nicely

REPLACEMENT PYREX DEPOSIT KARMA RDTA