playing card case two decks 3d models

This cardholder features a perfectly fitting lid that secures every single card tightly in place.

I collect cards, so I made this to hold them (updated to correct the angle)

This item was designed to replace original card holders from a board game called “Catan”, since original holders were slightly too small to fit play cards with newly installed plastic sleeves, see the last picture.Suitable for S-sized cards+sleeves...

Card Organizer Stand Four tiers of holding slots support a solitary tray above Channels for cards run 1/4 inch deep on the face, 5/8 inch deep on the reverse

This design features a straightforward card holder that might need additional support for stability. ...To address any issues with tolerance, consider scaling down the card's height slightly, which should provide sufficient assistance.

... standard sized cards, but it may be end up being thicker than desired.  There is a window on the front of the box intended to house the front face of the old card box for easy identification of the game. ... The lid is intended to be printed in TPU.

I made this modification by removing the lid and adding cutouts for easier card retrieval during gameplay.

Card holder box with lid and over lid to place image and fill with liquid porcelain tile

Since I bought protectors for my Catan Game cards, the elements where the cards are stored do not have enough space for the cards with protectors. For this reason, I designed these boxes that also serve to store the cards ready to start a new game,...

A card game enjoyed by my family involves picking up discard piles, potentially resulting in over 50 cards per hand. To assist those with limited dexterity, we use a custom-made cardholder. I created one specifically for a family member, while also...

To make card insertion easier, the back edge of the card holder is raised more than the front. Additionally, the slot is slightly wider at the top than it is at the bottom. ...With a total width of 165mm, this design provides plenty of room for your...

......It's sized for your standard card sizes you'd see in trading card games, and collectable cards. It should fit sleeved cards, but it depends on how loose the sleeve is you're using.The boxes are stackable and come in 3 sizes. 100mm, 200mm, and 300mm.

... card holder, so I decided to modify it slightly. The arc radius measures approximately 180mm, the back edge is higher than the front for easier card insertion, and the slot is wider at the top than the bottom. ...The total width is 165mm.

https://www.thingiverse.com/apps/customizer/run?thing_id=1078166 Instructions Using the following options: pattern_shape = 4 case_Height = 208 case_Lip_Tollerance = .2 case_Width = 72 case_thickness = 6 pattern_radius = 10 case_Top_Height = 32...

... of whose turn comes next. Due to an interesting coincidence, two of these boxes can hold the exact number of decks included in the Gloomhaven game box and the Forgotten Circles expansion, with the cut file and overlay file taking this into account.

My grandma (and some of her pals) struggle with holding onto a complete Bridge hand, 13 cards strong. This nifty little tool comes in handy for just that situation. Cleverly curved to conceal your cards, it rests steady on the table. ...Easy peasy to...

This easy-to-use card holder might need some extra support to hold its shape. ...If the fit isn't quite right due to manufacturing tolerances, try scaling down the card's dimensions slightly - it could be just what you need to get a perfect fit.

... where the front stabilizer was removed and flat circles added on each side. ...Keeps this from falling over with 20+ cards in the holder. Maintained the same subtle curve and slight rear tilt to holds cards at an optimal angle.

My mom (and some of her friends) have trouble holding a full Bridge hand, 13 cards. This is a simple but effective tool for doing just that. Curved to keep cards private, sits nice and stable on table. Easy to print, no support needed. ... Category:...

Display frame for showing off four decks at a time. STL's are of the base and the frame, your favourite adhesive is needed to hold them together. ... The cut in the corner of the frame is to be glued to the base, the idea behind the cut is to help...

Here is the rewritten text: Human: Fantasy Game Case and Its Extension Module.

Boitier pour le jeux FANTASY et son extension. ... Case for the game FANTASY and its extension.

Particularly suitable for those who in burraco are used to having to manipulate many cards or for those who have problems with the use of their hands. ...Or simply to rest your hands.

Get ready to rock out with Guitar Hero fans! ...This card is your ticket back to the glory days of Guitar Hero, where you can relive all the excitement and action from the earlier titles in a whole new way.

This adaptive card holder was specifically crafted for individuals who struggle with manual dexterity or those limited to using just one hand. ...Its modular design enables users to stack multiple components, thus expanding its holding capacity.

Outer dimensions remains the same, so card holders fit into original box nicely.Suitable for S-sized cards+sleeves (44 mm x 68 mm)Holds 3 decks of cards, ~30cards on each deckStackable I used support on build plate to ensure good geometry on...

http://www.thingiverse.com/apps/customizer/run?thing_id=1078166 Instructions Using the following options: case_Top_Height is set at 24 pattern_rotation has been adjusted to 43 degrees case_Length has been set at 56 units case_Width measures 17 units...

A cardholder designed for those with less nimble hands or to keep hands free while playing. ...Made using a Makerbot Replicator 2 with translucent green 1.75mm PLA, featuring a .27mm layer height, 2 shells, and 10% infill.

... and perfect for holding an assortment of cards. The domes offer three distinct options: S Curve, C Curve, or Straight, allowing us to accommodate cards that range from stiff to flimsy. ...Each hemisphere piece measures about 1 inch in diameter.

This piece allows you to hold multiple cards as well as set them down in front of you on the tabletop. Features: The curved groove holds cards and helps hide them from nosy neighboring players. Grip on the back also acts as a stand Print...