playing card shelf 3d models

A compact and straightforward holder for keeping regular-sized poker cards neatly organized.

Card holder for board games. ...Can be printed with space for 4 magnets (3mmx1mm)

A card holder I made that has the four decorative suits

UNO® card game replacement box with a separate compartment for the game instructions.

I collect cards, so I made this to hold them (updated to correct the angle)

This cardholder features a perfectly fitting lid that secures every single card tightly in place.

A comprehensive set of playing card tiles is ideal for rummy tile games like Rummikub. NOTE: If you want the tiles and also need the box that transforms into four tile racks, then you can get both the tiles and box here...

This series will be for playing card cases, regulation size, I have designed this to have a decorative bottom, and a logo on top, I *may* do dimensional logos, which would be a frame and a dimensional top you glue on. depends on the feedback. I tried...

Minimal card case, made for standard 54 cards deck. Uses four 4*2mm (diameter*height) neodimium magnets to keep it shut. Print in PLA or your favourite material. I think this "sheared" design looks particularly sleek in slightly translucent color...

This design features a straightforward card holder that might need additional support for stability. ...To address any issues with tolerance, consider scaling down the card's height slightly, which should provide sufficient assistance.

Card Organizer Stand Four tiers of holding slots support a solitary tray above Channels for cards run 1/4 inch deep on the face, 5/8 inch deep on the reverse

... standard sized cards, but it may be end up being thicker than desired.  There is a window on the front of the box intended to house the front face of the old card box for easy identification of the game. ... The lid is intended to be printed in TPU.

I made this modification by removing the lid and adding cutouts for easier card retrieval during gameplay.

This box will easily hold 2 decks of regular cards, since the Five Crowns game uses two 58 card decks. I printed it in 2 pieces and clicked them into place. ... I used .12 resolution and 30% infill with mine, but it should print fine with larger...

Card holder box with lid and over lid to place image and fill with liquid porcelain tile

Since I bought protectors for my Catan Game cards, the elements where the cards are stored do not have enough space for the cards with protectors. For this reason, I designed these boxes that also serve to store the cards ready to start a new game,...

I've heard people say I'm missing a few cards. ...But I'll never let my deck fall behind! This awesome card holder keeps all 54 cards in perfect order, safe from the dangers of being shuffled around or lost forever!

A card game enjoyed by my family involves picking up discard piles, potentially resulting in over 50 cards per hand. To assist those with limited dexterity, we use a custom-made cardholder. I created one specifically for a family member, while also...

To make card insertion easier, the back edge of the card holder is raised more than the front. Additionally, the slot is slightly wider at the top than it is at the bottom. ...With a total width of 165mm, this design provides plenty of room for your...

A versatile set of custom playing card tiles perfect for rummy tile games such as Rummikub and Mahjong. Each individual tile consists of three interlocking pieces that snap together with ease. The face, back, and insert pieces come together to create...

https://www.hornbach.cz/p/plastove-tesneni-k-prevlecne-matici-1-2-12x18x2/8463732/ Notes for assemblySee video :)Make sure smooth part sides (from printer bed) touch cards (especially for shuffler sides and plates) - cards need to easily slide on...

......It's sized for your standard card sizes you'd see in trading card games, and collectable cards. It should fit sleeved cards, but it depends on how loose the sleeve is you're using.The boxes are stackable and come in 3 sizes. 100mm, 200mm, and 300mm.

This replaces the box that the cards come in, as it eventually wears down and your cards begin to take a beating.  This is a remix from - https://www.thingiverse.com/thing:3324820The original was larger than it needed to be and has wasted...

... card holder, so I decided to modify it slightly. The arc radius measures approximately 180mm, the back edge is higher than the front for easier card insertion, and the slot is wider at the top than the bottom. ...The total width is 165mm.

A person suggests using a pack of cards since the original container has worn out and needs to be replaced, ideally one that is also waterproof.

A container specifically designed for holding standard decks of poker cards features reinforced flaps that securely fasten the hinged lid shut.

No more rummaging through cluttered drawers or searching for that one elusive card - with our box storage, everything is neatly stored and easily accessible. ... Enjoy the thrill of the game without any distractions - let our box storage take care of...

It's simply a standard card case. ...I remove the label from the lid and you can obtain the blank lid case by downloading it.

Printed 3D model designed to hold all the Gaia game cards. ...Simply fold the box insert and slide it into your storage case.

2022: Uploaded version 2:works with sleeved cards (added one more o-ring and removed all sharp edges in the card flow)the video shows how card blockers are set up - even 2 thin cards should be blockedto shuffle thicker cards, one should rotate faster...