playstation case 3d models

Raspberry pi 2/3 case in the format of a playstation 1 print top with full suport. ... Use 4 small screws 2,5 x 20mm to connect the top, bottom and raspberry.

Modeled after the Nintendo Switch Case holder here https://www.thingiverse.com/thing:5153942 Allows you to add additional left / right slots Recommend printing everything either at 98% or 99% on X axis, otherwise cases fit loosely, like original.

Modeled after the Nintendo Switch Case holder here https://www.thingiverse.com/thing:5153942 Allows you to add additional left / right slots Recommend printing everything either at 98% or 99% on X axis, otherwise cases fit loosely, like original.

Modeled after the Nintendo Switch Case holder here https://www.thingiverse.com/thing:5153942 Allows you to add additional left / right slots Recommend printing everything either at 98% or 99% on X axis, otherwise cases fit loosely, like original....

... fan grid intake. Added 2 screws on the bottom. Added a square hole to allow the raspberry camera cable to go trough it without being damaged by the usb ports. This model is based on : PiStation - Raspberry Pi 2/3 Case by jhample - Thingiverse

The Top and the Logo can be printed together with a MMU.Added a rear fan grid intake.Added 2 screws on the bottomAdded a square hole to allow the raspberry camera cable to go trough it without being damaged by the usb portsThis model is based on :...

Hello! ... New holder for Xbox, Playstation game cases from WLF Design. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: 6_height_tolerance = .2 4cornerR = 8 6swidth = 6.1 5width = 58.6 4swidth = 6.17 6width = 67 6Plus_perimeter_tolerance = .5 6length = 138...

I reworked the original PiStation to suit the Pi 4 dimensions. The Top and the Logo can be printed together with a MMU. The Top and the Logo can be printed together with a MMU. Added a rear fan grid intake. Added some mini clips. ...Added 2 screws.

This holder holds onyl 10 games and include PlayStation logo that can be printed separately and inserted into the case. ... Inspiration take from: https://www.thingiverse.com/thing:2595827

There are slots at the back to make it easier to get a game out of the case. I print them for separate game series, so there's a bit more space between the games of different franchises. ...This gives your entire collection an extra organized look!

Everybody who has more than 10 games need a big case for them. And if you don't have to much spaces to the sides, you must build it to the top. ...And here is solution :) The symbols will need a little sandpaper :)

Planned completion in Summer 2020 Controller in PS2-Design in Winter 2020 Update History Update 08/17: The Playstation case now consists of several parts, which I have separatly uploaded as .stl files Furthermore I have made a prototype of the memory...

**Work in progress** Playstation One Style Case for the LattePanda Alpha. ... More about the LattePanda Alpha: [dfrobot.com](https://www.dfrobot.com/category-177.html?src=lattepanda_site) Todo: * Make the buttons/LED work * Power On * Power...

Raspberry Pi 3 case shaped like the original Playstation. Opens with a hinge, has enough space for a fan. All ports accessible. The preview is a low res proof of concept. The hinge hole is designed to take a Q-tip shaft as a hinge bolt. **EDIT**...

this is a ps5 case mod from horizon forbidden west see the build video here. ...https://youtu.be/wbXT7CM8i-g

Check the video on YouTube. ... https://youtu.be/Np6JsaC-wBc Require a soft silicone protective case for WF-1000XM3

The Cyclone RX for Plastation controllers by KMTech doesn't come with a case so I made my own. Should click together but use glue if it keeps comming apart. Need to work on the captive screws not sure what thread they are or where to get them. But...

No supports needed. ...Infill at 20 and speed can be set at whatever works for you still prints well at higher speeds

Playstation 4 portable case

A simple case for a PS Vita with hinged lid and opened letters. I welcome any comments! ... Enjoy.

In the original model, the top and bottom were mixed up. ...Plus, the board of my memory card did not fit inside, the case did not close.

Instructions I made this one pictured out of glow in the dark filament so I could easily see the case at night. It's a nice fit, especially if you add some mole skin, fabric, or a couple strips of weatherstripping or something inside to prevent...

Display 12 of your favorite games for the Playstation Vita print the body and letters separatly to make color customization easy.

It's a case for the power supply of an old Playstation 1. There is a lid zo you can close it. The power supply can supply 7.6 V and 3.6 V. ...I only used 7.6V which is the brown and red wire.

Fits Raspberry Pi 2/3. ... Resembles PlayStation 2.

This is a PS Eye case with a GoPro Mount to mount your PS Eye Cam onto your 3D Printer. ... Parts needed: - 4x M3x8mm Screws (or M3x6mm) - the original screws which hold the cam in the original case

I Used Doble sided tape to stick to place, i swap cases often. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/47ZUFRlikbi

https://www.cgtrader.com/3d-print-models/games-toys/other/playstation-2-case-for-raspberry-pi-4b This case is still very early on and is the first revision. I will update it along the way. This case has enough space for an LOW PROFILE ICE TOWER air...

Case for RaspBerry Pi 3 of the Playstation 1 - In the process of improvement but I think it is already functional