ploopy 3d models

I adore the Ploopy Trackball, but its design didn't offer enough support for my wrist, so I created the Ploopy Wedge to provide that extra stability.

Replacement top piece to use 3 Bosch-Rexroth R053010810 ball transfer units (omnidirectional bearings) in the [Ploopy trackball](https://www.ploopy.co/trackball) with the original ball.

Ploopy Button - Raised M1 Was made to suit a more forward grip position on the Ploopy. ...Helps to avoid having to curl your thumb too much.

Ploopy Nano + BDN9 (I don't have a BDN9) Macro pad dimension area: Nano_BDN9.stl - 73.5mm x 73.5mm x 15mm Nano_BDN9_v2.stl - 74.1mm x 74.1mm x 15mm Ploopy Nano + YMD09 QMK Nano_YMD09 - 10.4 degrees of tilt, no access to reset port Nano_YMD09_v2 -...

 Ploopy Nano + BDN9 (I don't have a BDN9)Macro pad dimension area:Nano_BDN9.stl - 73.5mm x 73.5mm x 15mmNano_BDN9_v2.stl - 74.1mm x 74.1mm x 15mmPloopy Nano + YMD09 QMKNano_YMD09 - 10.4 degrees of tilt, no access to reset portNano_YMD09_v2 -...

I love the Ploopy Trackball but needed more of an angle for my wrist so I made the Ploopy Wedge. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .20 Infill: 15-35 Notes: I went with 35% infill to give the...

The nano top stl can be found here on the creator's github: https://github.com/gbrnt/ploopy-nano/tree/master/hardware/mechanicals-btu-mod/STLs This project also uses Socket Cap style M3 hardware: 4 - M3x8mm screws to attach the ring arms to the...

This is a remix of the Ploopy Pick-and-Place Feeder that has been modified to work with the Lumen PnP, along with several improvements to the basic mechanisms to improve reliability.Added a mounting bracket for installation on the Lumen PnP feeder...

I wanted to make a closed back for the Ploopy Headphones since it's nice to have the option. I have not tested this yet as I'm waiting for my pair to arrive! ...It should print fine.

This is my modification of the top shell of the ploopy thumb trackball (https://github.com/ploopyco/thumb-trackball) to convert it to use bearing-transfer-units. Originally discussed at...

Be careful not to go too deep - you can always drill out more after trying it * Try fitting the adapters into the slots in the Ploopy top part * If they don't fit well, take the adapters out and file any non-fitting bits. For me the one closest to...

I found the Ploopy kept swiveling around the anchor post and the cheap silicone feet I stuck on the bottom of the wedge kept sliding off because they used cheap adhesive. What it needed was some divots to accommodate the stock feet of the Ploopy to...

A modified scroll wheel to add clicks to the Ploopy Classic Trackball. Use in conjunction with a jumbo sized paperclip behind PCB situated as to push against the scroll wheel lightly. 9/19/21 Added Notched Version 2: Added bevel to top of wheel...

Prusa Mini+ .2 mm layer height 10% infill Prusament Galaxy purple PLA

Wanted a much less severe angle to match my keyboards better.

... and the Snooker ball with a Pool ball. ...Basically, it isn't a Nano anymore. Hardware needed:Ploopy Nano pcb and lense3 BTUs (https://store.livhaven.com/r053010810-bosch-rexroth-ball-transfer-unit)1 heatset insert (top half)1 M3 screw2 ¼" Pool ball

My newest design. Untested. My printer is busy at the moment. Be the first person in the world to try it out!!! ... Instructions to add click bar here: https://imgur.com/gallery/k8fGjrv

... is intended to use M3 Socket Cap screws (3 per side) to attach the mount to the modded Sofle Case. ...It then will attach to the Modded Ploopy Nano that that created here: https://www.printables.com/model/284971-norne-ploopy-crkbd 

That angle is then held in place by the threaded nut.The standoff piece is to be printed 10 times and is what holds the PCB to the case.The nano top stl can be found here on the creator's github:...

This is a modified head mount for the Opulo Lumen PnP machine that allows head-mounting a solenoid actuator for use with mechanically actuated feeders, such as drag feeders or my modified Ploopy Feeder.  If you want to have the right head...

On its own this isn't much use, it's just a prototype for testing a mod for the Ploopy trackball. v1: BTUs fit straight into BTU tester v2: BTUs fit into a sleeve, which fits into the BTU tester. The sleeve should be printed in TPU. ...Note that...