plow controller mount 3d models

This is a basic wall mount designed to keep your PSVR Aim controller secure and within easy reach. The mount itself is attached firmly to the wall using four small 3M Command strips. ...These strips are available for purchase on the official 3M website...

I designed this mount to seamlessly integrate with the Hobby King Quadcopter Power Distribution Board and compatible standard 36x36mm flight controllers such as the OpenPilot CC3D, Naze32, and Flip32 models. ...The distinctive Washington and Lee Trident...

This project allows for easy access to the hand controller and the mounting bracket can be stored flat as the Tripod Clips can be attached/detached via a bayonet feature. The cam lock features are glued onto the back of the mounting bracket at any...

So, after I built my turtle beach wall mount, I thought some of you might like a PS4 controller mount too. So, I knocked up this design - just print it on one of my printers and I'll upload a pick when finished. Recommend two 3.5mm x 35m wall...

So after everyone was talking about how the PS5 would have liquid metal damage if upright, and a lot of people started to lay it horizontally including myself, I decided to make this wall mount that would connect to the existing remix that I have on...

PS4 Pro Vertical Controller Mount This controller mount is designed to attach to a vertical PS4 Pro. ...There's enough clearance on the mount to charge the controllers while mounted. Post a make if you print this out! Print Settings Printer Brand:...

Mounting Hardware: 2x - M4 - 8mm bolts (secure mount to PSU) 8x - M3 - 12mm bolts/nuts (secure controller to mount) Links: MW LRS 350 - https://www.amazon.com/LRS-350-24-Enclosed-Switching-Replacement-Termina MW LRS 600 -...

Mounting Hardware: 2x - M4 - 8mm bolts (secure mount to PSU) 8x - M3 - 12mm bolts/nuts (secure controller to mount) Links: e6804 - https://sandevices.com/product/e6804-kit/ MW LRS 350 -...

Mounting Hardware: 2x - M4 - 8mm bolts (secure mount to PSU) 8x - M3 - 12mm bolts/nuts (secure controller to mount) Links: e682 - https://sandevices.com/product/e682-kit/ MW LRS 350 -...

Edit: I had to redesign the controller mount because the previous version looked nice but was a hassle to clean up and required too many rafts. This new design can be rotated to sit at the bottom and should not need any rafts, plus it's wider than...

Thanks to the original designer.Printed in PETG.For the print I put supports into the slot where the Controller goes and used PLA as Support interface for an easy and clean removal.I used M6x10 screws for mounting it to my sim rig.EDIT: Added a...

This bracket is designed with standard hole spacing, enabling the flight controller (NanoWii in my case) to be mounted on top while speed controller wiring, a receiver, and a Bluetooth module are discreetly hidden underneath. Everything fits neatly...

... I took it to the next level by incorporating nylon M3 washers and bolts for a sleek, low-profile design. To ensure maximum stability, print one of these genius mounts for each stand-off hole on your flight controller - that's 4 game-changing pieces!

A custom-designed wall mount for a headphone and an Xbox one controller. A blank model as well as the Avatar - The Last Airbender elements are added. The regular ones are for headphones with earcups that swivel. The extended ones for fixed...

In practice, the mount performs admirably, holding the controller firmly in place without slipping or falling out easily. ... For my own print, I used PLA with a 0.2 layer height and 25% infill - an arguably excessive combination that yielded...

After purchasing a Valve Index, I wanted a similar mount for the knuckle controllers, so I made one. I used the base plate of the HTC Vive model and added four simple hooks for the knuckles to hang on. I used double-sided tape for the HTC Vive...

... through a smaller hole and attach a servo or manually adjust it for control. Print Settings Printer: Da Vinci Junior Rafts: No Supports: Yes Resolution: Any Infill: 10-20 Notes: It is recommended to expand the width of the plow during assembly.

There were a bunch of xbox controller mounts but nothing i saw for PS4. Definitely a bunch that could be done to optimize/clean this up but i lack the patience and competence to do it. ... I printed with supports and you can clearly see in the...

Quest 3 controller wall mount. Can be attached to the wall using some regular drywall screws, or command strips (or similar) if desired. Designed it to be compact so you can fit them inside the strap like shown. I did put the controllers in a swapped...

Mini Talon Flight Controller Suspension Mount. Suppress vibrations to your Flight Controller using this tray that clips under wooden wing box. Has larger holes to keep it light & 4 - 5mm holes for rubber dampeners. Also has 4 holes for zip ties to...

 The controller and headset mounting points are a bit further apart, and the lip that holds the bottom of the controller has been extended a bit.  Hole spacing is the same, so it should be a drop-in replacement if you already put one on your wall.  I...

Xbox One and 360 controller mount made specifically for mounting under a desktop. Options include Wired, Wireless, and Razer Sabertooth. The original design is based on Hegmar's Xbox One Controller Wall or Furniture Mount. Update (2017-02-19): Added...

Hi Everyone, the newly designed and titled "Under Desk Universal Controller Mount" is now available for you to download. Like all of our other mounts and stand it's a universal design so just about all controllers should work with it. We are using...

... of the bed at all. NOTE: The cable connecting the controller to the motherboard was not long enough on my machine to reach this far. ...It was therefore required to use a little extension cable in order to be able to reach the offline controller.

This is a remix of @RyanZ's LCD clip included with the LowRider2 files to fit his  Full Graphic Smart Controller Case.This version allows the clip to fit on my TRUSS MOUNT FOR GNARLY RAMBO CASE. The truss mounts slot into the recesses in...

... infilling and produce a very solid piece when using ABS as I do. M3 screws and nuts secure the PWM controller firmly to the mount, and there are four mounting holes for M5 screws to attach the mount securely to your machine or other application.

I built a mount for my new PWM fan control board so that I can attach it to my printer. The holes are drilled for 3mm bolts that go from below up to secure the board in place. It's something I whipped up quickly, but maybe others will find it useful...

I have included two versions, one for screw mounting and the other for use with command strips or mounting tape. *A note on printing, I designed this for aesthetics and not ease of printing. While it's absolutely printable in its standing position...

Modification of Xbox One Controller Phone Mount by WhatTheActual01. This rotates the phone 90° as some games require. It will hold nearly all of the latest larger phones. ...The end notches also have been resized to hold a phone with up to a 12mm thick...

This is a wall mount for playstation 4 dualshock controller. It has the playstation logos integrated in its design. The logo is a separate file so as to be able to print it a different color and insert it into the main piece. The logo in the front is...